40mm crank, pistons, rods

Alex170984
Club4AG Expert
Posts: 332
Joined: Thu Jun 20, 2013 4:08 am

40mm crank, pistons, rods

Postby Alex170984 » Mon May 09, 2016 5:00 am

I have recently acquired a corolla block and head. The head is not for sale but the crankshaft, pistons and conrods are all for sale.

I would prefer these go together. They were removed from a car that had done 85k miles and they are all in excellent condition.

I will post up pictures later on when I get home. The pistons have been cleaned and have come up like new!

No bearing wear on crank at all.

Please bear in mind this is the 40 mm crankshaft with the smaller rods.

Make me a respectable offer.

Cheers

Disable adblock

This site is supported by ads and donations.
If you see this text you are blocking our ads.
Please consider a Donation to support the site.


Alex170984
Club4AG Expert
Posts: 332
Joined: Thu Jun 20, 2013 4:08 am

Re: 40mm crank, pistons, rods

Postby Alex170984 » Mon May 16, 2016 12:10 pm

Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image

All rods are matching to their original pistons and we've numbered all the rod caps up so they are not mismatched when the bearings are replaced.

sirdeuce
Club4AG Pro
Posts: 661
Joined: Mon Jan 14, 2013 9:47 pm
Location: Sierra Nevada foothills

Re: 40mm crank, pistons, rods

Postby sirdeuce » Mon May 16, 2016 3:01 pm

Those look like the 10-1 comp pistons. Too bad the shipping kills the deal for me.
One shot, one kill.

User avatar
Rogue-AE95
Club4AG Expert
Posts: 452
Joined: Thu Jan 10, 2013 4:03 pm
Location: Tampa Bay, FL

Re: 40mm crank, pistons, rods

Postby Rogue-AE95 » Mon May 16, 2016 3:43 pm

I was just thinking the same thing, that those must be the 10.1:1 pistons.
'88 Corolla All-Trac

Disable adblock

This site is supported by ads and donations.
If you see this text you are blocking our ads.
Please consider a Donation to support the site.


Alex170984
Club4AG Expert
Posts: 332
Joined: Thu Jun 20, 2013 4:08 am

Re: 40mm crank, pistons, rods

Postby Alex170984 » Tue May 17, 2016 1:44 am

They are out of a 85' corolla so surely they are 9.4:1?

Alex170984
Club4AG Expert
Posts: 332
Joined: Thu Jun 20, 2013 4:08 am

Re: 40mm crank, pistons, rods

Postby Alex170984 » Tue May 17, 2016 3:48 am

Sorry can this advert be deleted until I decide what to do with these.

These pistons should have featured in the MR2 originally me thinks instead of the low comp pistons!

sirdeuce
Club4AG Pro
Posts: 661
Joined: Mon Jan 14, 2013 9:47 pm
Location: Sierra Nevada foothills

Re: 40mm crank, pistons, rods

Postby sirdeuce » Tue May 17, 2016 7:11 am

What the engine came out of makes no difference really, unless you know absolutely that it was original. Most of our cars these days are mix and match.
One shot, one kill.

Alex170984
Club4AG Expert
Posts: 332
Joined: Thu Jun 20, 2013 4:08 am

Re: 40mm crank, pistons, rods

Postby Alex170984 » Tue May 17, 2016 8:21 am

It was original. The bloke is a Corolla nut ;)

User avatar
oldeskewltoy
Club4AG MASTER
Posts: 1898
Joined: Wed Jan 09, 2013 4:44 pm
Location: Portland, Oregon

Re: 40mm crank, pistons, rods

Postby oldeskewltoy » Tue May 17, 2016 8:30 am

Those are indeed 10:1 4AGE pistons (9.4:1 engines are actually 4AGEC engines - "C" stands for catalyst equipped ) These pistons were in some areas in Europe, and in Singapore, where no cats were required. 4AGEC TVIS 9.4:1engines make 112-115hp, smallport makes 130hp, the Singapore, and some areas of Europe TVIS 10:1 piston versions are alleged to make 125hp


Image
OST Cyl head porting, - viewtopic.php?f=22&t=300

Building a great engine takes knowing the end... before you begin :ugeek:

Enjoy Life... its the only one you get!

sirdeuce
Club4AG Pro
Posts: 661
Joined: Mon Jan 14, 2013 9:47 pm
Location: Sierra Nevada foothills

Re: 40mm crank, pistons, rods

Postby sirdeuce » Tue May 17, 2016 11:03 am

Funny how they reduce the efficiency of combustion to improve emissions. Things are getting better though.
One shot, one kill.

Disable adblock

This site is supported by ads and donations.
If you see this text you are blocking our ads.
Please consider a Donation to support the site.



Return to “4A-GE Engine Parts”

Who is online

Users browsing this forum: No registered users and 2 guests