20v swap guys I need your input!!

User avatar
alavelle12
Club4AG Enthusiast
Posts: 90
Joined: Sat Jan 19, 2013 2:41 pm

20v swap guys I need your input!!

Postby alavelle12 » Wed Dec 04, 2013 1:54 pm

Ok for all you guys running 20v swaps, what clutch/flywheel setups are you running and how do you like them? I'm going to be doing some drifting/spirited driving with mine and am trying to figure out the best setup for me.

Thanks,
Alec

Disable adblock

This site is supported by ads and donations.
If you see this text you are blocking our ads.
Please consider a Donation to support the site.


MisterJerk
Club4AG Pro
Posts: 581
Joined: Wed Jan 09, 2013 6:10 pm

Re: 20v swap guys I need your input!!

Postby MisterJerk » Thu Dec 05, 2013 4:11 pm

you can get away with the stock clutch/flywheel. Unless you like to clutch drift, or just beat up the clutch when you drive.

teamkunimitsu
Club4AG Regular
Posts: 22
Joined: Mon Jan 14, 2013 10:04 pm

Re: 20v swap guys I need your input!!

Postby teamkunimitsu » Tue Dec 31, 2013 9:29 am

yes if your in a budget stock flywheel will do but a lightened flywheel will really wake up the motor response wise.

NZ4age
Club4AG Regular
Posts: 13
Joined: Mon Jan 28, 2013 8:14 pm
Location: New Zealand

Re: 20v swap guys I need your input!!

Postby NZ4age » Wed Jan 01, 2014 12:58 am

Had one of these in my old one, great clutch and can take a bit of a beating, nice in the traphic too, don't get too much of a dead leg. http://japrace.com/products/Exedy-Sport ... E-20v.html , on blacktop 20v flywheel which is lighter than silvertop 20v, lighter flywheel would definitely make it rev better and quick but loose torque
88 AE92 GTi-16 Corolla
83 AE85 4AGE Trueno Sprinter
91 Levin GTZ
02 Caldina GT-Four N-spec

Admin of Facebook groups - 4AGE~4AGZE~4AGTE (English), Toyota 3sgte (English), Caldina Club NZ and Models, Diecast's & RC (English)

Disable adblock

This site is supported by ads and donations.
If you see this text you are blocking our ads.
Please consider a Donation to support the site.


yoshimitsuspeed
Club4AG MASTER
Posts: 2084
Joined: Sun Jan 13, 2013 1:18 pm
Contact:

Re: 20v swap guys I need your input!!

Postby yoshimitsuspeed » Wed Jan 01, 2014 7:54 am

NZ4age wrote: lighter flywheel would loose torque

That is completely untrue. A lighter flywheel will free up power across the board. The only place it will sacrifice it in stored inertial energy when launching.

Personally this is the clutch I would go with.
http://matrixgarage.com/products/act-sp ... -kit-212mm

If it's mating to a RWD trans you will need this bearing. http://matrixgarage.com/products/exedy- ... earing-t50

The other option would be to put a 200mm flywheel on it and getting a standard AE86 disk and PP in it.

Disable adblock

This site is supported by ads and donations.
If you see this text you are blocking our ads.
Please consider a Donation to support the site.



Return to “TECH: 4A-GE ENGINE”

Who is online

Users browsing this forum: No registered users and 7 guests