Oldeskewltoy..do you have a better pic of the trd sump pan at the far right? Can you send it to my pm please? I may also have a buyer for that other front cover for you as well..thanks!

Payment sent..

Nice! Man those tail LEDs are cool as heck..!

Yeah nice taco mtmetzger! I also take on those trials that's less traveled too hahah..! Hey my daughter also drives a 06 TRD taco & she wheels it whenever she gets a chance. It runs in the family

I'd try putting a taper on the leading & trailing edge of those pads & see if that helps. Are you runnin drilled/slotted rotors miswuevos?

Removed my front struts to do the strut housing mod, for new short stroke shocks.

Max..got the crank sprocket today. Thanks!

Mike

I have a set 40/20 early rods.. The small end has been machined out to 20mm for pressed pins. If interested lmk

^^All of the above are good & valid points guys..lets just hold back for a bit & wait for ismael's findings on that starter signal wire allencr said to check

If connections are good, battery's strong,& ground is good to the block..then go grab a buddy & have him turn & hold the ignition key down to start, while YOU with a hammer reach down & lightly tap the starters solenoid. If it engages & starts, get a new starter or replace the co...

yangster wrote:thanks guys but, do u guys know which wire exactly? I don't know which one would be the 12v wire.

An sr5 visited my shop this morn..yellow wire. Good luck!

I'd just get the adj link bars to get the axles pointing straight again, & do what ga_goosh said if noise is a concern. Nice car btw!

rumsawatti=if your not sure of the cars mechanical state, mileage & god knows whatever else he's not disclosing, dont take that risk in offering anything yet..Meet up with the guy & car in person. Drive it, then negotiate with an offer

danhtruong wrote:thank you Mike! you are my hero . My friend weld it for me, everything ready to do, my job right now is cut metal and buy a lateral rod.

Thumbs up..!

I saw the dyno specs for the tomei 5 valve & it makes good power up to 7500, also stating "excellent turbo response"..
Kelford has more cam selections for 20v's, but no dyno charts to compare

Unrelated side question. Is it a terrible idea to completely disassemble a dizzy? As in removing the stuff inside that says "don't remove" in bold letters? Yea it might be. But to swap internals over, hey who hasnt? I think theres a proceedure to set the pickup coil projection (or signal ...

What was the mileage on it?

No I'm afraid not..do you still have the stock carb by any chance? There were a couple elec plug connections on the stock carb, do you remember disconnecting them? If you don't have the carb anymore, that's ok. Look at the pass fender well area.. These plug connections (female end) should all be the...

Green thing meaning a plug? Get a test probe to find a 12v + power (key on) in that green plug. Connect the choke to this power source.

danhtruong= Metric bolt & nut for the hanger bracket is a hexagon flanged 14x1.5mm size bolt & is approx 2-1/2" long. On the other end (on axle) there should be a stud only w/nut of the same exact thread size.

I've got a set of these tomei cams, but I'm curious as well

Took pics of my lat/rod hanger in hopes of helping a fellow club member..furthering the removal of bolts for specs info..
I feel good:D

Oh' dayuum, those longchamps just gave me a woody!
Nice find VirtriumGTS..

Yeah & I'll report back for the 130 as well

Yup..track or street, safety is first bud.
Ummm..both? But just remember, there was only one that started it all........THE AE86!!!

I'll get those bolts sizes for ya' in the morn, kinda tired right now _._

Yeah, can i have the size of all bolds, I ask the alignment guy he said get the aftermarket lateral rod which can adjust (godspeed lateral rod) and try to make the hold closet to the oem as much as possible. He said the lateral rod doesnt hold any load so the bracket dont have to be that strong. Af...

This is useful info here about alts.& amps

Red=I did see the difference in the 130 & 118 stator sizes. Got both alts at the shop n i noticed it. Was gonna use the larger of the two, but now,,nope!

hachi2k..jus noticed the samurai sword shifter. Nice touch!

Umm,after thinking about this, I'm gonna let them practice on beater car first. Then we'll see..

mrkona wrote:Still need a crank pulley thanks

Pm sent!