Search found 435 matches

by phanist
Tue May 13, 2014 3:18 am
Forum: TECH: Corolla AE86
Topic: Wheel fitment question. 15x9 and/or wider
Replies: 5
Views: 1750

Re: Wheel fitment question. 15x9 and/or wider

15x9 0 offset is do able for the rear without flair but like above said you need the roll the hell out of that fender lip and pull like crazy the. Use 205 or below... Now for front 15x9 same offset not do able unless you rock some crazy negative camber and crazy roll/pull and trim/remove inner plast...
by phanist
Tue May 13, 2014 3:08 am
Forum: TECH: Corolla AE86
Topic: Group buy on high quality header feeler
Replies: 89
Views: 14345

Re: Group buy on high quality header feeler

I believe the cusco mount lower engine down by 10mm...

Yoshi i too have the cusco engine and tranny mount when try to fit that silkroad mani.....
:(
by phanist
Tue May 13, 2014 12:39 am
Forum: TECH: Corolla AE86
Topic: 20v swap ignition problems?
Replies: 1
Views: 547

Re: 20v swap ignition problems?

Was the wire harness self built? Or purchase .. Sound like wiring peoblem
I would check all the plug make sure they are tight and connected . Try a different set of cop try 1nz
I heard some got better luck with them.
by phanist
Tue May 13, 2014 12:35 am
Forum: TECH: Corolla AE86
Topic: Group buy on high quality header feeler
Replies: 89
Views: 14345

Re: Group buy on high quality header feeler

Ouch.... What was it hitting? The drive shaft? Or the rack?
by phanist
Mon May 12, 2014 7:23 pm
Forum: TECH: Corolla AE86
Topic: Group buy on high quality header feeler
Replies: 89
Views: 14345

Re: Group buy on high quality header feeler

Yes sir i like how your design look too. I can live with that...
by phanist
Fri May 09, 2014 10:33 pm
Forum: TECH: Corolla AE86
Topic: Group buy on high quality header feeler
Replies: 89
Views: 14345

Re: Group buy on high quality header feeler

The 20v dont have a problem with your design...
Make me a stainless first?
by phanist
Fri May 09, 2014 6:13 pm
Forum: TECH: Corolla AE86
Topic: Group buy on high quality header feeler
Replies: 89
Views: 14345

Re: Group buy on high quality header feeler

Came up with anyhing new ?
by phanist
Fri May 09, 2014 1:37 pm
Forum: Shops, Manufacturers, and Retailers Only
Topic: zenki GTS twin cam graphics
Replies: 13
Views: 3775

Re: zenki GTS twin cam graphics

Door side Gts twin cam 16
Trunk/hatch GTS and corolla
No toyota decal.
by phanist
Wed May 07, 2014 1:03 am
Forum: TECH: Corolla AE86
Topic: Group buy on high quality header feeler
Replies: 89
Views: 14345

Re: Group buy on high quality header feeler

Rhd will have better fitment ... It the Lhd that have issue with exhaust manifold
by phanist
Tue May 06, 2014 11:44 am
Forum: Shops, Manufacturers, and Retailers Only
Topic: zenki GTS twin cam graphics
Replies: 13
Views: 3775

Re: zenki GTS twin cam graphics

I dont remember there is a smaller twin cam 16 decal... Just a super large like first post pic then the front fender decal and rear fender decal and the hatch/trunk corolla gts decal

The smaller gts twin cam i believe is for the 1986-1987 usdm model year
by phanist
Mon May 05, 2014 10:35 pm
Forum: TECH: Corolla AE86
Topic: Group buy on high quality header feeler
Replies: 89
Views: 14345

Re: Group buy on high quality header feeler

Yah i can live with that like what TOR said

Fitment 16/20v
by phanist
Mon May 05, 2014 6:23 pm
Forum: Shops, Manufacturers, and Retailers Only
Topic: zenki GTS twin cam graphics
Replies: 13
Views: 3775

Re: zenki GTS twin cam graphics

Hey man

You need the truck or hatch decal to complete the set... You should a decal that say
Toyota or it is corolla
by phanist
Sun May 04, 2014 12:06 pm
Forum: TECH: Corolla AE86
Topic: Group buy on high quality header feeler
Replies: 89
Views: 14345

Re: Group buy on high quality header feeler

Yes sir in did... It look good too... The rise is high enough..
But you were worry about the dizzy and ppl have to change to the aw11 dizzy... For me i dont care i got a 20v no dizzy there for me
by phanist
Sun May 04, 2014 3:33 am
Forum: TECH: Corolla AE86
Topic: Group buy on high quality header feeler
Replies: 89
Views: 14345

Re: Group buy on high quality header feeler

Well from the jsp design.. I dont have any knownledge of the performance gain of it but i would prefer to have a higher rise primaries .. If you were to go with the jsp route make sure at least make sure your design could still be able to use the PS and Ac unit... As i believe with the jsp you wont ...
by phanist
Sat May 03, 2014 6:16 pm
Forum: TECH: Corolla AE86
Topic: Group buy on high quality header feeler
Replies: 89
Views: 14345

Re: Group buy on high quality header feeler

Update?? The rise height of the pic above first pic.. Seem to be a 4-1 .... But make it 4-2-1 instead?
by phanist
Fri May 02, 2014 1:28 am
Forum: Shops, Manufacturers, and Retailers Only
Topic: TORPARTS - JDM Parts
Replies: 33
Views: 13922

Re: TORPARTS - JDM Parts

mideng

got any kouki front grill in stock?
by phanist
Thu May 01, 2014 1:22 pm
Forum: TECH: Corolla AE86
Topic: Group buy on high quality header feeler
Replies: 89
Views: 14345

Re: Group buy on high quality header feeler

Yes sir that cover plate between them is what i describe... I just dont know what is the proper term to call it. :)

Yoshi i remember both passenger and driver side have that plate.
by phanist
Thu May 01, 2014 12:20 pm
Forum: TECH: Corolla AE86
Topic: Group buy on high quality header feeler
Replies: 89
Views: 14345

Re: Group buy on high quality header feeler

yoshi you are doing a 4-2-1 not a 4-1 right? andothing thing the engine mount bracket on your mock up car.... pic above there should be a sandwich like metal plate between the metal bracket to block and hard rubber to subframe.. i think it about 2-5mm thick...that can be a factor if clearing the PS ...
by phanist
Thu May 01, 2014 2:28 am
Forum: TECH: Corolla AE86
Topic: Group buy on high quality header feeler
Replies: 89
Views: 14345

Re: Group buy on high quality header feeler

Yehaaaa finally you got something going... Let see it...
by phanist
Wed Apr 30, 2014 9:09 pm
Forum: TECH: Corolla AE86
Topic: Group buy on high quality header feeler
Replies: 89
Views: 14345

Re: Group buy on high quality header feeler

Update us Sir !!!!
Let see some photo type at lease
by phanist
Wed Apr 30, 2014 1:27 pm
Forum: TECH: 4A-GE ENGINE
Topic: What PS bracket do I need?
Replies: 14
Views: 2197

Re: What PS bracket do I need?

Saigone Hey if the ps pump is mounted on that bracket that also hold the idle pulley and if the ps pulley line up with the crank then? Why is that the idle is off align? From picture on first post... That look normal... On my the idle thingy is a bit off too like 1-2mm and it been running fine i rev...
by phanist
Tue Apr 29, 2014 11:55 pm
Forum: TECH: Corolla AE86
Topic: 4AGE Not Running Right
Replies: 22
Views: 3070

Re: 4AGE Not Running Right

was it running like **** when you just buy the car?....
by phanist
Tue Apr 29, 2014 6:02 pm
Forum: TECH: 4A-GE ENGINE
Topic: Another 20v with idles problems
Replies: 12
Views: 1968

Re: Another 20v with idles problems

Check too see if your brake boost vacuum line are loose? And port that you may have gap off are loose? Clean your throttle make sure nothing is keeping the butterfly open when you release throttle.
by phanist
Tue Apr 29, 2014 3:19 pm
Forum: TECH: Corolla AE86
Topic: 4AGE Not Running Right
Replies: 22
Views: 3070

Re: 4AGE Not Running Right

If the hard starting issue happen after you adjust your tps then you should be paying attention to that instead of digging into other things. Because while you start to remove other part again and you may mess more thing up... Just saying...
by phanist
Tue Apr 29, 2014 12:38 am
Forum: TECH: 4A-GE ENGINE
Topic: Another 20v with idles problems
Replies: 12
Views: 1968

Re: Another 20v with idles problems

jondee in the case of the 4 air bleed screw on each individual itb that you stated is factory setting and should never be mess with.. then how do we know if it been mess with or not?. is there a way to find out? after all i/we or most of us got the 20v used from importer.. unknown if any of this hav...
by phanist
Tue Apr 29, 2014 12:32 am
Forum: TECH: Corolla AE86
Topic: 4AGE Not Running Right
Replies: 22
Views: 3070

Re: 4AGE Not Running Right

what condition were you car running in when you first buy the car?. running nicely ? but just idling at 1.1k rpm? and rise from 1k to 1.1k? then you decided to adjust the tps? then it get worst? then that your problem there....the tps position incorrectly... i don't think your idling at 1k rpm to 1....
by phanist
Fri Apr 25, 2014 3:35 pm
Forum: TECH: Corolla AE86
Topic: Ae86 20v bt warm up time?
Replies: 4
Views: 970

Re: Ae86 20v bt warm up time?

Yup i did notice that the engine seem to warm up about a miles or so too.. I guess im just trying to compare tuis bt to another stock daily cars vans truck etc... Idk for what reason did i just started to want to warm up my engine before driving it off.. Maybe because i thought that is a good thing ...
by phanist
Fri Apr 25, 2014 12:00 pm
Forum: TECH: Corolla AE86
Topic: Ae86 20v bt warm up time?
Replies: 4
Views: 970

Re: Ae86 20v bt warm up time?

really? i never have a car that take that long to warm up...
by phanist
Fri Apr 25, 2014 1:51 am
Forum: TECH: Corolla AE86
Topic: Ae86 20v bt warm up time?
Replies: 4
Views: 970

Ae86 20v bt warm up time?

Hi club4ag Ok so i been fight this pass fews week to get my blacktop 4age swap to run right. So now i start up and idle at about 900 rpm but my question is . How long should it take to warm up to idli g temperture? My take about 8minute and some 30second. That is if i just start engine and just leav...
by phanist
Wed Apr 23, 2014 11:02 pm
Forum: TECH: 4A-GE ENGINE
Topic: 20v BT 7age is build underway
Replies: 51
Views: 11845

Re: 20v BT 7age is build underway

Sorry v33sonata i did not mean to jump in on ypur thread or any.. If any you would more about a 7ag then i ever could learn about it.. To those who wonder about the blacktop ecu on the 7ag bt ...im not sure if it would work... I just happen to have something which look like a 20v bt 7ag sitting in m...

Go to advanced search