Search found 542 matches

by ga_goosh
Fri Aug 16, 2013 1:21 pm
Forum: TECH: Corolla AE86
Topic: Levin/Trueno Rad. Support and sub-assy the same?
Replies: 3
Views: 900

Re: Levin/Trueno Rad. Support and sub-assy the same?

if you are asking if the levin front will bolt to the trueno rad support the answer is yes. im not sure if they are the same tho
by ga_goosh
Fri Aug 16, 2013 1:07 pm
Forum: Wheels, Tires, Suspension
Topic: WTT: work equip wheel caps
Replies: 0
Views: 859

WTT: work equip wheel caps

I have a set of Brand new wheel caps. one has been opened to test fit on my work wheels but since my wheels are the old 80s style 1 piece they dont fit. I would like to trade these caps for a set of center line pop in caps in good to new condition or a set of the older style work equip caps. let me ...
by ga_goosh
Fri Aug 16, 2013 11:18 am
Forum: TECH: Corolla AE86
Topic: Help plz CUSCO Rear Tribar Install Help plz
Replies: 6
Views: 1412

Re: Help plz CUSCO Rear Tribar Install Help plz

I would think some large washers would help as well to prevent the bolts from being pulled through the sheet metal.
by ga_goosh
Fri Aug 16, 2013 4:26 am
Forum: TECH: Corolla AE86
Topic: Check Engine Light is on...NEED HELP!
Replies: 6
Views: 1513

Re: Check Engine Light is on...NEED HELP!

if your cel is staying on then pull the codes your self. that will give you a general starting point at least. also try ti repair the original harness to save those dollars 2 grand is not worth it you can get your harness completely repaired for about 500 bux from a good professional
by ga_goosh
Wed Aug 14, 2013 2:56 pm
Forum: Want to BUY (seeking sellers)
Topic: WTB blacktop/ silvertop 8bolt flywheel or compatible
Replies: 5
Views: 1236

Re: WTB blacktop/ silvertop 8bolt flywheel or compatible

I have a 200mm 8 bolt flywheel and clutch from a ae92 for 50 + shipping. yes the mr2 will also.
by ga_goosh
Wed Aug 14, 2013 2:42 pm
Forum: Want to BUY (seeking sellers)
Topic: WTB 7 Rib block assembly
Replies: 2
Views: 935

Re: WTB 7 Rib block assembly

I have a 7 rib block rods and pistons but no crank if your interested. i can throw in a crank but i dont think it is usable but your machinist might have a different opinion then mine does. i will sell them for 125 + shipping.
by ga_goosh
Wed Aug 14, 2013 2:37 pm
Forum: Want to BUY (seeking sellers)
Topic: Looking for fuel fitting
Replies: 3
Views: 968

Re: Looking for fuel fitting

get one from a civic. its not exactly the same but it is a lot easier to find and it works. iv used one when my tvis plate was removed.
by ga_goosh
Tue Aug 06, 2013 6:21 am
Forum: 4A-GE Engine Parts
Topic: 4age block rods/pistons and flywheel
Replies: 9
Views: 2138

Re: 4age block rods/pistons and flywheel

bump make a reasonable offers and will accept trades for a 42mm crank and 20v exhaust cams maybe other parts so just make offers thanks
by ga_goosh
Mon Aug 05, 2013 1:47 pm
Forum: Want to BUY (seeking sellers)
Topic: TW: BT or 42mm crank 20v exhaust cams
Replies: 3
Views: 950

Re: TW: BT or 42mm crank 20v exhaust cams

I have an exhaust cam and gear from a B/T. I also have a 42mm crank, still in the block. Journals are standard and the crank is straight. what price are you looking for for both shipped to 77584? also are all the rod and main journals good? will i have to do any machining to the crank? and what eng...
by ga_goosh
Fri Aug 02, 2013 1:33 pm
Forum: AE86 Parts & Accessories
Topic: yearly Garage Sale...north NJ
Replies: 82
Views: 17162

Re: yearly Garage Sale...north NJ

Ill take 36, 58, 100, 84, 57, 85
by ga_goosh
Fri Aug 02, 2013 9:19 am
Forum: TECH: Corolla AE86
Topic: Enkei Compe 15" x 8", 205 - Help with offset
Replies: 17
Views: 6111

Re: Enkei Compe 15" x 8", 205 - Help with offset

SidekickChuck wrote: I have a 10 inch rear wheel (0 offset with a moderate 1 inch spacer) with 225's and there is still some room left inside the fender.


this is the same thingas 15x8 -25 and the car pictured has fender flares???
by ga_goosh
Fri Aug 02, 2013 9:16 am
Forum: TECH: ZN6, ZC6 (FR-S,BRZ,86)
Topic: Greddy Racing Sport Exhaust -- How do I make it cooL?!
Replies: 2
Views: 3144

Re: Greddy Racing Sport Exhaust -- How do I make it cooL?!

^^lol you can maybe find a local fiber glass shop to make a single exhaust rear valence or some sort of cap that will cover the other side. Maybe get your local body shop to work some auto body magic and cut and patch it to remove it. why not get creative and get a single round fog light and hook it...
by ga_goosh
Fri Aug 02, 2013 8:03 am
Forum: Want to BUY (seeking sellers)
Topic: TW: BT or 42mm crank 20v exhaust cams
Replies: 3
Views: 950

TW: BT or 42mm crank 20v exhaust cams

I am testing the waters to see what is available. I will need shipping as i am in TX. I am mostly looking for a Black top crank in good usable condition but i will consider any 42mm crank. let me know what you have with a shipping price and detailed pics of all main and rod journals. I would also fe...
by ga_goosh
Fri Aug 02, 2013 6:11 am
Forum: TECH: Corolla AE86
Topic: Enkei Compe 15" x 8", 205 - Help with offset
Replies: 17
Views: 6111

Re: Enkei Compe 15" x 8", 205 - Help with offset

I dont think the 15x8 +25 will clear the front strut casings. i could be wrong but that is a whole inch closer then the 0 offset and the 15x8 0 offset is pretty close to the strut casing as it is. -25 offset and you will be closer to the fender but i dont think you will get 205's on the -25 offset u...
by ga_goosh
Fri Aug 02, 2013 6:01 am
Forum: TECH: 4A-GE ENGINE
Topic: Much difference BT or ST flywheel combined with C52?
Replies: 2
Views: 935

Re: Much difference BT or ST flywheel combined with C52?

flywheels really dont do anything for acceleration it will do more for throttle responce tho. your engine will rev a bit quicker but like stated above when you are in gear driving down the road you probably wont notice a whole lot. if you are all ready in there then go for it it deffinately wont hurt
by ga_goosh
Fri Aug 02, 2013 5:42 am
Forum: AE86 Parts & Accessories
Topic: need rwd water pump pulley
Replies: 1
Views: 665

Re: need rwd water pump pulley

I have one ill sell for 25 + shipping. LMK send me a pm and ill respond faster thanks
by ga_goosh
Tue Jul 30, 2013 2:29 pm
Forum: 4A-GE Engine Parts
Topic: 4age block rods/pistons and flywheel
Replies: 9
Views: 2138

Re: 4age block rods/pistons and flywheel

according to fedex it will be about 150 to 175 sent by fed ex ground. i can check other shipping places like ups and usps but i dont think usps will ship it due to the weight.
by ga_goosh
Tue Jul 30, 2013 2:23 pm
Forum: Want to BUY (seeking sellers)
Topic: Looking to buy a few parts. Mostly transmission stuff
Replies: 7
Views: 1589

Re: Looking to buy a few parts. Mostly transmission stuff

I have a used clutch and flywheel that is in good shape the clutch disk is 7.6mm thick and i have a t50 shifter. ill throw in the shift knob for free I also have a large port oil pan and windage tray. oil cooler hose fitting is still there too with drain plug. LMK
by ga_goosh
Tue Jul 30, 2013 2:09 pm
Forum: Want to BUY (seeking sellers)
Topic: WTB: Clutch/pressure plate
Replies: 6
Views: 1274

Re: WTB: Clutch/pressure plate

I have a 200mm clutch with pressure plate that has 7.6mm of meat left. well with in spec ill sell it for 30 + shipping LMK. I have a 200mm 8 hole flywheel also if you need it
by ga_goosh
Tue Jul 30, 2013 2:05 pm
Forum: 4A-GE Engine Parts
Topic: 4age block rods/pistons and flywheel
Replies: 9
Views: 2138

Re: 4age block rods/pistons and flywheel

bump
by ga_goosh
Fri Jul 26, 2013 11:13 pm
Forum: 4A-GE Engine Parts
Topic: 4age block rods/pistons and flywheel
Replies: 9
Views: 2138

Re: 4age block rods/pistons and flywheel

bump
by ga_goosh
Thu Jul 25, 2013 8:58 am
Forum: TECH: Corolla AE86
Topic: Worn Out Driveshaft Center Bearing
Replies: 8
Views: 1643

Re: Worn Out Driveshaft Center Bearing

I would say the center bearing are worn. i had the same issue on my drive shaft. if you look on amazon you can find a chinese center bearing for about 15 bux or so. if you want the oem bearing then expect to pay about 80 bux to 120. it does sound like with all the play that your center bearing is ba...
by ga_goosh
Thu Jul 25, 2013 5:36 am
Forum: TECH: Corolla AE86
Topic: 14s vs 15s
Replies: 6
Views: 1457

Re: 14s vs 15s

I prefer 14 over 15 14 are usually lighter then most 15 in general but not always. also with 14 you can run a shorter tire and still have a decent side wall. I run a 14x8 with a 185/55-14 tire. not only do i still have a 55 seriese side wall but it also changes the final drive ratio to about 4.5:1 r...
by ga_goosh
Thu Jul 25, 2013 5:32 am
Forum: TECH: 4A-GE ENGINE
Topic: Frankenstein 4A-GE smallport questions
Replies: 3
Views: 1241

Re: Frankenstein 4A-GE smallport questions

I think you can use the large port afm as long as it comes from the 88 - 89 corolla gts. according to toyodiy it says they use the same afm. as for the large port from the ae86 im not sure about how it will work with the small port ecu :/ about using the 4af block, it will work. you should check the...
by ga_goosh
Mon Jul 22, 2013 1:16 pm
Forum: AE86 Parts & Accessories
Topic: •For Sale (SoCaL) AE86 Parts & Stuff!*
Replies: 283
Views: 61056

Re: 7/20/13 UPDATED For Sale (SoCaL) AE86 New Lower Price!!!

free bump for peter he is a great seller
by ga_goosh
Mon Jul 22, 2013 12:36 pm
Forum: 4A-GE Engine Parts
Topic: 4age block rods/pistons and flywheel
Replies: 9
Views: 2138

Re: 4age block rods/pistons and flywheel

bump
by ga_goosh
Mon Jul 22, 2013 9:51 am
Forum: Want to BUY (seeking sellers)
Topic: WTB Looking for these bolts turbo mani
Replies: 9
Views: 1295

Re: WTB Looking for these bolts turbo mani

where you bought these header they should give you a part list of whats included. what kind of headers are these? i got it from someone but there were no studs with it I have some used 4age OEM studs with nuts if you want. let me know how many you need and ill see how many i have. if anything i kno...
by ga_goosh
Mon Jul 22, 2013 7:49 am
Forum: TECH: Corolla AE86
Topic: 88 Nova
Replies: 7
Views: 1348

Re: 88 Nova

I would say get all your parts from an 88 - 89 corolla gts and i am willing to bet it will just fall together like it was actually a corolla.
by ga_goosh
Fri Jul 19, 2013 1:48 pm
Forum: 4A-GE Engine Parts
Topic: 4age block rods/pistons and flywheel
Replies: 9
Views: 2138

4age block rods/pistons and flywheel

I have for sale 4age 7 rib block from a 88 corolla gts large port $75 + shipping 4 42mm/20mm pistons and rods 9.4:1 comp ratio also from a 88 gts corolla large port for $50 + shipping 200mm 8 bolt flywheel and used clutch for sale $50 + shipping. next is a zenki welded diff. no r&p no pumkin. ba...

Go to advanced search