Search found 14 matches

by TopshelfJason
Tue Oct 13, 2015 8:48 am
Forum: AE86 Parts & Accessories
Topic: FS/FT: 1987 SR5 Red Coupe Partout
Replies: 18
Views: 3773

Re: FS/FT: 1987 SR5 Red Coupe Partout

Do you still have the passenger side quarter panel replacement? Interested in it, shipped to va.


Sent from my iPhone using Tapatalk
by TopshelfJason
Tue Oct 13, 2015 7:08 am
Forum: OWNERS and BUILDERS
Topic: AE86 TopShelf build
Replies: 16
Views: 4641

Re: AE86 TopShelf build

So after wiring in the 1nz cops the car works a little better, the misfire under load disappeared. But I'm not out of the woods yet, it's running really lean/rough and won't idle to save its own life. I initially used the base map diy auto tune has available but it's garbage. I ended up importing my...
by TopshelfJason
Sun Sep 27, 2015 8:31 am
Forum: OWNERS and BUILDERS
Topic: AE86 TopShelf build
Replies: 16
Views: 4641

Re: AE86 TopShelf build

I had to take a hammer to that area to allow the cup to sit further up and flush, you also have to do this if you plan on adjusting the spring perch to make the car go as low in the rear as they will allow. Otherwise you'll have to leave the perch 1/2-3/4 of a inch away from the top of the cup, whic...
by TopshelfJason
Thu Sep 24, 2015 4:10 pm
Forum: OWNERS and BUILDERS
Topic: AE86 TopShelf build
Replies: 16
Views: 4641

Re: AE86 TopShelf build

Got the fortune auto coil overs installed on my AE86 today. The installation went about how you would expect it to go, kind of like the 5 stages of grief, denial, anger, bargaining, depression, and finally acceptance. I learned a lot of things as well like the top hats are side specific for the fron...
by TopshelfJason
Fri Sep 18, 2015 8:04 pm
Forum: OWNERS and BUILDERS
Topic: AE86 TopShelf build
Replies: 16
Views: 4641

AE86 TopShelf build

The car ran for the first time tonight. Got my diypnp megasquirt from the builder tonight, loaded firmware(wrong one), then loaded the msq file. After some finagling with the settings due to the wrong initial firmware we got the car to fire and run better than it's ever run. Now I need to put a new ...
by TopshelfJason
Wed Sep 16, 2015 3:27 pm
Forum: OWNERS and BUILDERS
Topic: AE86 TopShelf build
Replies: 16
Views: 4641

Re: AE86 TopShelf build

I'm not doing body work, I'm paying a guy who does the best work ive ever seen to do it. But if the panel is too far gone and needs to be replaced i needed to know where to start looking. Thanks for the help.


Sent from my iPhone using Tapatalk
by TopshelfJason
Tue Sep 15, 2015 6:48 pm
Forum: OWNERS and BUILDERS
Topic: AE86 TopShelf build
Replies: 16
Views: 4641

Re: AE86 TopShelf build

Quick question I'll post here because I don't want to clutter up other threads. The rust on the rear passenger side quarter panel behind the door, does anyone make replacement sheet metal for that that I can weld in?


Sent from my iPhone using Tapatalk
by TopshelfJason
Tue Sep 01, 2015 12:40 pm
Forum: 4A-GE Engine Parts
Topic: Toda 20v cam gears, OEM VVT gears, T3 crank pulley, etc.
Replies: 49
Views: 12087

Re: Toda 20v cam gears, OEM VVT gears, T3 crank pulley, etc.

It won't let me reply with a pm. Shoot me your email and I'll give you my address.


Sent from my iPhone using Tapatalk
by TopshelfJason
Tue Sep 01, 2015 12:20 pm
Forum: 4A-GE Engine Parts
Topic: Toda 20v cam gears, OEM VVT gears, T3 crank pulley, etc.
Replies: 49
Views: 12087

Re: Toda 20v cam gears, OEM VVT gears, T3 crank pulley, etc.

I'll send a payment on Monday when I get back from vacation. Just shoot me your PayPal info and I'll send my address.


Sent from my iPhone using Tapatalk
by TopshelfJason
Tue Sep 01, 2015 12:12 pm
Forum: 4A-GE Engine Parts
Topic: Toda 20v cam gears, OEM VVT gears, T3 crank pulley, etc.
Replies: 49
Views: 12087

Re: Toda 20v cam gears, OEM VVT gears, T3 crank pulley, etc.

Oem preferred.


Sent from my iPhone using Tapatalk
by TopshelfJason
Tue Sep 01, 2015 11:40 am
Forum: 4A-GE Engine Parts
Topic: Toda 20v cam gears, OEM VVT gears, T3 crank pulley, etc.
Replies: 49
Views: 12087

Re: Toda 20v cam gears, OEM VVT gears, T3 crank pulley, etc.

Need three intake valves for a st. Let me know price. Shipped to Virginia.


Sent from my iPhone using Tapatalk
by TopshelfJason
Tue Sep 01, 2015 10:23 am
Forum: OWNERS and BUILDERS
Topic: AE86 TopShelf build
Replies: 16
Views: 4641

AE86 TopShelf build

Lame, everyone who has them posted for sale need to update the websites then. Here's a little teaser shot [img]http://images.tapatalk-cdn.com/15/09/01/134f5b9f9ef2532a1bd60f8314a99c30.jpg[/img] http://images.tapatalk-cdn.com/15/09/01/9267322c4c9fff025c860aa3e4965b04.jpg While the head and valves wer...
by TopshelfJason
Fri Aug 28, 2015 9:16 am
Forum: OWNERS and BUILDERS
Topic: AE86 TopShelf build
Replies: 16
Views: 4641

Re: AE86 TopShelf build

Oem rear, true coil rear wasn't done when I ordered them. Oem rear has enough adjustment to get the proper ride height I wanted so it was just the natural choice.


Sent from my iPhone using Tapatalk
by TopshelfJason
Tue Aug 25, 2015 6:32 am
Forum: OWNERS and BUILDERS
Topic: AE86 TopShelf build
Replies: 16
Views: 4641

AE86 TopShelf build

I had another account on here but I've forgotten my login info, either way it was a just a thread about how I was having trouble getting my 16v running. Jump forward many months and I've given up on the 16v(it's forsale btw). But I'll post some of my progress here, it will be a lot of explaining and...

Go to advanced search