Search found 137 matches

by mr2mk1hero
Sat Sep 19, 2020 2:43 am
Forum: TECH: 4A-GE ENGINE
Topic: OST-070: 7AGE for an N2 Levin
Replies: 30
Views: 24857

Re: OST-070: 7AGE for an N2 Levin

I have never seen a better way to see actual porting results than that blue rubber thing :) "I have used other valves to protect seats when I've done the chamber work in the past - when I have machined seat to protect, in this case the seats haven't been cut, so I didn't need to protect them.&q...
by mr2mk1hero
Fri Sep 18, 2020 11:36 pm
Forum: TECH: 4A-GE ENGINE
Topic: Ideal intake length for stock 4AGE 16v bigport?
Replies: 21
Views: 14300

Re: Ideal intake length for stock 4AGE 16v bigport?

jondee86 wrote:Feels more like this :D :D

Image

Cheers... jondee86


:lol: :lol: :lol: :lol: :lol:
by mr2mk1hero
Fri Sep 18, 2020 11:33 pm
Forum: TECH: 4A-GE ENGINE
Topic: Anyone retrofitted oil squirters?
Replies: 0
Views: 2738

Anyone retrofitted oil squirters?

Hi guys, Anyone ever retrofitted piston oil squirters to a 4A block? I'm doing a turbo build and I'll be using 4AGZE low comp pistons and aftermarket forged rods. Like all aftermarket forged rods mine don't have the hole that spits oil onto the cylinder, like stock rods do. So I'm concerned about pi...
by mr2mk1hero
Sat May 09, 2020 9:23 am
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30325

Re: HIGH comp Big port carby build with MANY questions

https://www.jetsrus.com/ These guys have pretty much every jet in every size you can imagine. Ok I had two pretty successful carb settings. Carbs are 36.5mm Keihin from CBR600 F4. First setting is on the rich side 3 turns out pilot screws stock pilot jets (42) jet needle on two factory washers (stoc...
by mr2mk1hero
Sat May 09, 2020 8:52 am
Forum: TECH: 4A-GE ENGINE
Topic: The actual potential of the 4AFE cylinder head?
Replies: 6
Views: 12176

Re: The actual potential of the 4AFE cylinder head?

Ok engine is in https://i.ibb.co/BzphtWv/IMG-20200508-165307.jpg I didn't have much time to mess around with it, but I couldn't resist removing the intake manifold to see what kind of ports I have. https://i.ibb.co/MDWzyWJ/IMG-20200508-171212.jpg So as you can see I have the same thing as OST-044, w...
by mr2mk1hero
Thu May 07, 2020 3:55 pm
Forum: TECH: 4A-GE ENGINE
Topic: The actual potential of the 4AFE cylinder head?
Replies: 6
Views: 12176

Re: The actual potential of the 4AFE cylinder head?

The engine was supposed to arrive today but it didn't. Here's a pic of it until it arrives tomorrow: https://i.ibb.co/drJp5Fw/4af.png It's from a 1996 European Toyota Carina E (gen 3 they call it here), so it's a 2nd gen 4af and pretty recent by 4A standards. I did read that Bill's page a few times ...
by mr2mk1hero
Thu May 07, 2020 3:37 pm
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30325

Re: HIGH comp Big port carby build with MANY questions

As someone who has gone through a carb build here's my advice. Get an AFR gauge if you haven't already. I think I remember your name actually, we messaged on Instagram once? And I mentioned an AFR gauge? Tuning carbs without one is just guesswork. Someone with A LOT of experience can tune carbs with...
by mr2mk1hero
Thu May 07, 2020 12:38 am
Forum: TECH: 4A-GE ENGINE
Topic: The actual potential of the 4AFE cylinder head?
Replies: 6
Views: 12176

The actual potential of the 4AFE cylinder head?

Hello my good 4age people, long time no see! I have a pretty serious and maybe somewhat complicated question to ask, but I know this forum has more than a few individuals capable of providing some valuable input. You might know the car and engine I'm currently running. The bike carb 4age in my aw11 ...
by mr2mk1hero
Mon Dec 23, 2019 2:45 am
Forum: TECH: 4A-GE ENGINE
Topic: 4AGE crank sensor brackets on SALE
Replies: 0
Views: 5014

4AGE crank sensor brackets on SALE

Hi all, I'm discontinuing the production of my 4AGE crankshaft sensor brackets. So everything is on sale as I clear stock: https://www.driving4answers.com/shop/ I have sold over 200 of these over the past 2 years to more than 20 different countries around the world with absolutely ZERO complaints. I...
by mr2mk1hero
Thu Sep 26, 2019 12:45 am
Forum: TECH: 4A-GE ENGINE
Topic: 4K to 4AGE cnc distributor adapter group buy
Replies: 3
Views: 7071

4K to 4AGE cnc distributor adapter group buy

A while ago I made a billet 4k to 4age distributor adapter for a customer on my cnc. I posted some pictures on Instagram and a few people asked me to make one for them. The deal is that making this thing one a time doesn't really make sense, so I decided to see if there's enough interest for a group...
by mr2mk1hero
Wed May 30, 2018 10:42 am
Forum: TECH: 4A-GE ENGINE
Topic: 4AGE crankshaft position sensor bracket
Replies: 0
Views: 3478

4AGE crankshaft position sensor bracket

https://s33.postimg.cc/h8gxrspy3/DSC_0446.jpg So here's the reason progress has been slow recently with my aw11 bike carb 4age build. I have been working on improving the design of my crankshaft position sensor bracket for the 4age engine and putting it on the market. Compared to my prototype and v...
by mr2mk1hero
Fri Apr 20, 2018 6:45 am
Forum: TECH: 4A-GE ENGINE
Topic: 4age on bike carbs
Replies: 30
Views: 36930

Re: 4age on bike carbs

She is alive! https://youtu.be/24XLDCwBqP4 I figured out how to work around the COR. I replaced it with a tachometric relay from a BMW. Seems to work great. I will soon post full details on the wiring. There were some initial issues with the start up, I had a kink I missed in my fuel supply hoses. R...
by mr2mk1hero
Fri Apr 20, 2018 6:19 am
Forum: TECH: 4A-GE ENGINE
Topic: OST-047: Skippy Replicate
Replies: 13
Views: 10474

Re: OST-047: Skippy Replicate

Ha! Awesome story! Glad to hear she went to good hands and will be used properly :)
by mr2mk1hero
Fri Mar 30, 2018 11:18 am
Forum: TECH: 4A-GE ENGINE
Topic: Ignition key source
Replies: 5
Views: 5604

Re: Ignition key source

Use the original wires where possible. So use the black and red ecu power wire to power up the ecu, use the coil and igniter power wire to power up your new coil(s) this is probably black and orange. http://club4ag.com/tech-data/tech-specs/4a-ge-16v-japan-ae86-ecu-pin-identification/ According to t...
by mr2mk1hero
Wed Mar 28, 2018 4:28 pm
Forum: TECH: 4A-GE ENGINE
Topic: Ignition key source
Replies: 5
Views: 5604

Re: Ignition key source

Thanks! I'm trying to wire in my nodiz standalone ignition ecu.
by mr2mk1hero
Wed Mar 28, 2018 1:10 pm
Forum: TECH: 4A-GE ENGINE
Topic: Ignition key source
Replies: 5
Views: 5604

Ignition key source

So I'm doing a bunch of wiring and have a really stupid newby question. What is a good wire to use an ignition key source, so something that will be powered on when the key is in the on AND start positions and powered off when the key is in the off position. What would be a good wire to tap in for t...
by mr2mk1hero
Tue Mar 20, 2018 1:55 am
Forum: TECH: 4A-GE ENGINE
Topic: 4age on bike carbs
Replies: 30
Views: 36930

Re: 4age on bike carbs

You will need a fuel pump so you will need a relay so you might as well keep the Circuit Opening Relay (COR) It has 5 wires but you will only need 3, I don't know AW11 wire colours but they may be similar to an AE86. Black and Red is ignition positive, equivalent to pin 30 and 85 combined. Black an...
by mr2mk1hero
Sun Mar 18, 2018 9:08 am
Forum: TECH: 4A-GE ENGINE
Topic: 4age on bike carbs
Replies: 30
Views: 36930

Re: 4age on bike carbs

1. The tacho signal comes from the igniter (black wire with red rings in an AE86) it is also in the diagnosis connector as IG- if you trace this wire inside the car you can find where to connect your new ecu output to it. Also you may need to use a tacho adapter between your ecu and the rev clock, ...
by mr2mk1hero
Thu Mar 15, 2018 11:36 am
Forum: TECH: 4A-GE ENGINE
Topic: 4age on bike carbs
Replies: 30
Views: 36930

Re: 4age on bike carbs

So today I decided to hack up my wiring harness. I realized that I can have a very nice and clean engine bay by amputating a lot of the connectors from the wiring harness, since I won't need most of them anymore, considering my fuel supply will be handled by the bike carbs and my ignition by the nod...
by mr2mk1hero
Mon Feb 26, 2018 5:59 am
Forum: TECH: 4A-GE ENGINE
Topic: OST-045: 5AGTE.... again ;)
Replies: 26
Views: 17932

Re: OST-045: 5AGTE.... again ;)

Amazing work as always. How the heck do you get those shallow coolant passages around the chambers so clean? One of the costs.... I have each head cleaned and pressure checked at a machine shop. In this case the head did come to me cleaned already, but I still had it checked for its pressure holdin...
by mr2mk1hero
Fri Feb 23, 2018 1:09 am
Forum: TECH: 4A-GE ENGINE
Topic: OST-045: 5AGTE.... again ;)
Replies: 26
Views: 17932

Re: OST-045: 5AGTE.... again ;)

Amazing work as always. How the heck do you get those shallow coolant passages around the chambers so clean?
by mr2mk1hero
Mon Feb 19, 2018 12:54 am
Forum: TECH: 4A-GE ENGINE
Topic: 4age on bike carbs
Replies: 30
Views: 36930

Re: 4age on bike carbs

would like see how are you planning to hold the magnetic sensor, to feed the NODIZ thanks It's being made right now. Here's what I did. I took my old busted oil pump and installed it along with a gasket and a busted crankshaft on an old junkyard block I had sitting around. I then Installed my T3 pu...
by mr2mk1hero
Wed Feb 14, 2018 9:11 pm
Forum: TECH: 4A-GE ENGINE
Topic: 4age PCV how does it work
Replies: 12
Views: 14760

Re: 4age PCV how does it work

So basically it won't work because there is too much vacuum in the intake manifold?

What if I add an actual pcv valve somewhere before the intake manfiold?
by mr2mk1hero
Wed Feb 14, 2018 5:12 am
Forum: TECH: 4A-GE ENGINE
Topic: 4age PCV how does it work
Replies: 12
Views: 14760

Re: 4age PCV how does it work

Alright, definitely makes more sense. Took me forever to figure out the system counting down from atmospheric pressure. So, any thoughts on my pcv system for the bike carb conversion? "So for my bike carbed 4age setup I am thinking about having a hose from the cam cover breather go to a catch c...
by mr2mk1hero
Wed Feb 14, 2018 1:27 am
Forum: TECH: 4A-GE ENGINE
Topic: 4age PCV how does it work
Replies: 12
Views: 14760

Re: 4age PCV how does it work

Thanks guys it's clear now. What they were essentially trying to do is to separate the vapors from the oil itself. That damn complicated baffle inside the cam cover finally makes sense. It's there to help prevent oil getting picked up. They didn't plug the pcv hose into the manifold itself because t...
by mr2mk1hero
Mon Feb 12, 2018 10:27 am
Forum: TECH: 4A-GE ENGINE
Topic: 4age PCV how does it work
Replies: 12
Views: 14760

4age PCV how does it work

Was looking at the intake manifold today and got curious. I always thought that outlet for the pcv on the intake manifold is simply open on the other end, i.e. the crankcase vapors go to the manifold, but they don't, rather they seem to end up somewhere in the throttle body? Why is that? And why doe...
by mr2mk1hero
Mon Feb 05, 2018 10:21 am
Forum: TECH: 4A-GE ENGINE
Topic: 4age on bike carbs
Replies: 30
Views: 36930

Re: 4age on bike carbs

I am back and I bring you the funk! https://youtu.be/daqmPnEYMfk I also bring you some pictures of the newest iteration of my pride and joy: (this forum refuses to pick up my images. Works with zero issues on other forums, so club4ag gets links, sorry) http://www.driving4answers.com/wp-content/uploa...
by mr2mk1hero
Wed Jan 24, 2018 1:37 am
Forum: TECH: 4A-GE ENGINE
Topic: Temperature sender question
Replies: 1
Views: 2880

Temperature sender question

Just a quick question. I have been looking at the ECU pinouts to try and figure out the temp sender and temp gauge and their wiring. As far as I figure I don't need the stock ECU in order to keep the coolant temperature gauge working properly. All I need is the temp sender and it's connection to the...
by mr2mk1hero
Thu Jan 18, 2018 5:44 am
Forum: TECH: 4A-GE ENGINE
Topic: head work or bottom end?
Replies: 15
Views: 12065

Re: head work or bottom end?

I'm really no expert when compared to some of the guys on this forum, but I think working on the block and working on the head really go hand in hand and separating them is weird. A lot of compression without the right cams makes no sense, just like aggressive cams with stock compression also don't ...
by mr2mk1hero
Mon Jan 15, 2018 5:08 am
Forum: 4A-GE Engine Parts
Topic: FS: Various 4age bluetop (early bigport) parts and more
Replies: 6
Views: 6535

Re: FS: Various 4age bluetop (early bigport) parts and more

I have gray connectors with 2 pins each. Not to derail a Buy-Sell-Trade topic into technical talk, but that distributor might be off an AE92. For the US market, I know for a fact that the smallport dizzy has two small-ish grey plugs, smaller than the two round AE86 / AW11 connectors. I'm not sure a...