I have something like this. Hope it will help
https://drive.google.com/open?id=0B4nDB ... m9ydEVCUjQ

Thanks for pictures but none of them I can't use. I have some awkward connectors different from yours. I have gray connectors with 2 pins each.
Sorry for bothering

do you have some heat shields?

Hi,
can you post a picture of
- Late bigport (redtop) distributor

I have smallport head with bigport cams but I dont have that kind of issue
Idling at 10deg @ 800rpm like a charm

Willing to buy good condition 272 cams for 16V.

@jondee86 how did you know?
you're 100000% right. this little **** wasnt bolted to the intake manifold...
after engine rebuild I've replaced bigport head and intake with smallport and on this spot where bigport had screw smallport doesnt.
Found it yesterday and bolted.

my friend have found the problem :) the problem was ECU grounding, 3 pins on ECU are GND but none of them where connected to - So the only GND pin on ECU was O2 GND, and when I disconnect O2 sensor I cannot start the car because it does not close the circuit... Temporary we've grounded ECU so I can ...

Better quality image. AFM pinout and wiring diagram.
LINK

What are those two pins for on AFM ECU?
HT & OX?
How they work?

When I remove O2 sensor, my car won't start..

http://postimg.org/image/5vgbydky7/

Im disconnecting oxygen sensor because I wont to install DIYPNP and LC-1 wideband.
I ment oxygen sensor sorry

Hello everyone, I have trouble with my car. Its ae92 4AGE AFM bigport. When I disconnect oxygen sensor i have the problem with power inside my car. 1. So my oxygen sensor is disconnected, ingnition switch is in OFF position car has power.. 2. Oxygen switch disconnected, ignition switch is in ON posi...

quick update on project. Engine runs nice, better then the old one :) I've tried to put DIYPNP in my car but got some issues that need to fix before. I've loaded firmware into my DIYPNP loaded base map from website, calibrated all sensors, everything by the book. When I start the car I got jumpy RPM...

cj20vae86 wrote:460cc injectors

do you want to sell me injectors?

cj20vae86 wrote:I have 460cc yes

I have sent you pm few days ago and you said you would check for shipping costs. got no answeer after that...

still have injectors?

At the moment I am in the at the beginning of breaking in my engine, running it till 3000 rpm for 1000km. after that I will instal megasquirt and 235cc injectors from smallport.

Guys engine is in the car and running.
Setup is the same as before.
bigport block
smallport pistons with smallport rods
smallport head with bigport cams
and 0.4-0.5mm head gasket for 7AFE

hi,
do you have connection rods, whats the price?

hi,
do you have 4agze connection rods, whats the price?

You will need to cut-n-shut the smallport intake manifold and delete the TVIS plate. OR , use the bigport RWD intake manifold with a bigport-smallport adapter plate. Cheers... jondee86 I got smallport head with intake manifold. As mentioned the TVIS isn't a problem. Just leave it unplugged. Fueling...

@davew7 thanks for info :) @oldeskewltoy yes Im using smallport oversized pistons and NPR Europe piston rings, everything will be inside 3rib block. for the head I will use smallport head with bigport camshafts (friend has the same setup). basicly I wanted smallport head because air flow is better a...

Hello everybody, I hope someone could help me. At the moment I am in the process of rebuilding my 4AGE engine. I want to replace bigport head with smallport head, what will happen with the TVIS activation on the ECU side? When rebuild is done I will drive it for ~1000km till 3000 rpm, so I can be su...

Hey mate,
nice to see that your project goes fine.
we talked via google talk if you remember

what parts have you missing?

Thats just for harness and distributor, do you have ecu, sensor, or what else is needed?

can you tell me what is the price?

what about the price?

Europe=>Serbia=>Belgrade
whats the price for kit?

I am interested in buying MAP conversion kit