awesome sauce mates!perfect a clean like mine!+ 20bhp from me!

Hey everyone I am new to this club. I was wandering if there a repair manual specifically for the 89 corolla gts/ ae92? Just to clarify I am assuming my car is a large port with 7 rib or is it a small port. I am planning to rebuild it. The repair manual is the same with ae86 in the most of cases , ...

hello thats the parts needed for turbo the 4age 16v?what about ecu ?can be done with oem ecu? You could easily hit 150+ WHP turbo on the stock ECU. Much more than that and you will probably want to move to proper engine management. http://www.matrixgarage.com/content/yoshimitsuspeeds-guide-turboing...

You would need the following : Turbo manifold turbo oil lines downpipe intercooler intercooler piping blow off valve That's about it. Now as to how much it costs will depend on the parts you choose, new used etc. Finally you will need some form of fuel management. For a low boost you can suffice wi...

ronny wrote:you need a techtom software to remap stock ECU's

Technosquare does this ecu flash for most Toyotas - i had my map ecu flashed there years back.

Is this possible?Cause all the mechanics say that they are locked!

No i havent afm.My engine is map sensor equipped!

i have an ae92 corolla hatch.It is the 2nd tvis version european specs with 10.1 pistons and rebuilded with shaved head about 3/10 of a milimeter (if i am writing it right) These cams can play on my setup? The poncams should work great with your motor. If you have a non O2 ECU I don't know for sure...

i have an ae92 corolla hatch.It is the 2nd tvis version european specs with 10.1 pistons and rebuilded with shaved head about 3/10 of a milimeter (if i am writing it right)
These cams can play on my setup?

since i ve made some small changes to my engine eg a small comporession bump from oem 10.1 to eg 10.6 cr , a 20v header with custom free flaw exhaust system, a more free flow intake the Bmc Cda, a higher octane gazoline 100 octane ,a 100% synthetic 10w40 oil ,one of the best the amsoil amo and 20v c...

thank you s24a! i have not a flowmeter, i have map sensor based system (the oem one).So whatever i set at the co value as the load increases the ecu will use some different map and in case is wrong ,it will try to "correct" it. Now i am thinking tommorow to change the advance from 10 to 12...

I am trying to understand if the factory specs is equal to a specific lambda value and all together to an optimum afr. If you are looking for theoretical "best specifications" for A/F ratio on an engine , it is defined as "Minimum Best Torque" for the engine, which is the leanes...

I am trying to understand if the factory specs is equal to a specific lamda value and all together to an optimum afr.

totta crolla wrote:Set the co% to factory specs. and ignore the lambda reading.

why is this mate? and after some time factory specs will alter again?

good morning,
i have no o2 sensor and no catalytic converter.My car is a 1988 2nd generation 4age 16v tvis engine european specs.Ae92 hatchback corolla.So for adjusting the co idle mixture i have to connect it with co analystist and set it to 1.5% co + - 0,5 % from my variable resistor.

hello mates! Today i did a general check my mechanic, the engine is senond gen tvis 16v 4age european specs.No catalytic converter so the co idle mixture should be adjust from the variable resistor. I check my co at idle at about 800 rpms and was 0.24% better than a catalytic :P So we adjust it at a...

hello mates, below you can see some pictures from my blacktop 20v flywheel that installed to an ae92 2nd gen 4age 16v.I also bought and a 20v pressure plate and clutch disc to fit correctly. http://img607.imageshack.us/img607/2630/m0h7.jpg also changed the oil seal down there with toyota genuine one...

hello mate!this is the air temperature sensor!it sends signals to ecu by changing its resistance, as the temperature changing !

Hello and good morning!have you relocate the battery?and where exactly?thanx

http://i79.photobucket.com/albums/j143/oldeskewltoy/Loynings%20selloff/newTRDcrank_zps4b11f183.jpg authentic TRD crank $2500.00.... rods I already mentioned main caps need to be made for each application. Loynings, Hasselgren, and a few others do this kind of work, you might find a local shop capab...

Hello!
I am asking an ae92 gti front bumber in a good condition, preffered to be in europe for low cost shipment!thanx
I am asking if they are are availiable the bumber arm assy left and right too.

the porting is handmade?or have been on a machine shop ?

seems to be a very decent work! Good morning!

hello mate do you have pistons too ?

for the history the only thing that has failed afte 20+ years is the igniter......have tried another one ?

the later models or the 4afe had an extra vacuum valve for the power steering wheel.When you turn the power steering the valve opens and idle rises.

the job of this valve is to raise the idle about 200 rpms when a) you press the brake pedal b) when you turn on the lights c) when you turn on the blower d) when radiator fan opens. Sorry if i forgot something!

flywheel weight mate?

i am posting new photos from the starter relocation job and the 20v clutch flywheel installation ! http://img69.imageshack.us/img69/2707/na1q.jpg http://img547.imageshack.us/img547/2223/hnkh.jpg http://img5.imageshack.us/img5/907/chq4.jpg http://img842.imageshack.us/img842/1008/j324.jpg http://img31...

hello guys... i have the trans out....and i am relocating the starter....the coolant pipe needs to be modified a bit...so i send it to a local machinery shop....

i want to apologize about the wrong information i gave some days ago.The pressure plate of my 16v and the clutch disc that was finally 200mm does not fit the 20v flywheel.So i bought a new 20v clutch set for fitting..Tommorow i will send the presure plate and the flywheel for balancing.