Do you think if I tried 47 foot pounds it would put me more into spec? Like I said before I only did 43 Ft pounds. Thanks for the help makes me feel better knowing I don't have a lemon.

Also just to add the Haynes book said 43Ft pounds for the main bearings. I'm not sure how accurate that book is. I've see online people saying its 47Ft Pounds. Just added a little more info that might help.

Long story short I plasti gauged my new ACL main engine bearings and its out of spec. It came out to .051mm the Haynes book says .012mm to .039mm that's for 4ag engines years 86 and 87. 1985 says .012mm to .049mm I'm using a crank out of a 3 rib 4ag so 1985 crank in my GZE block. Stander bearings so...

So I used 300 grit sand paper it didn't take much but the lifters slide right now. Thanks a lot everything looks good to go now.

Okay after further inspection I can feel a small lip on the very top of the bores only cylinder one intake side. It catches my finger nail. I got the exhaust side lifters to fit in. So what should I do to make them fit? Should I get like 1000 grit sand paper or a file? I know it's easy to take off a...

Hello eveyone ive been doing a complete rebuild of my head and i tried to install the lifters on cylinder 1 but they wont go in. Ive got all of the other lifters installed they just slide right in. Ive even tried switching the lifters around but still nothing. Its like the hole is to small but only ...

I pulled my oil pan to tap for another oil drain. I found lots of metal shavings so I took a look at the bearings and it didn't look good. The connecting rods didn't have bearings at all and are damaged very badly. Also looks like the crank and rods are damaged. So my question is can I use the Conne...

I still need a clean passenger fender please help.

Please help Need Fender.

In Need of Right Passenger Fender!

Parts Parts Parts Need More Parts!

Please Help.

Need Parts Please Help.

I still need Fender and Fuel Pump Bracket.

Please Help.

Still Looking Please Help.

Hello Everyone Just looking for some parts.

Ae86 Right Fender Passenger.

Call Text Email

Email Alvarado.e09@gmail.com

5o5-65-Nine-2465

Bump

Im looking for the water pipe that connects to the rear of the water pump RWD set up. Its the long pipe that runs under the intake manifold and has a nipple to send coolent to the throttlebody.

Also looking for the fuel sending unit.

Call Text Email

505-659-2465
Alvarado.e09@gmail.com

Still Looking for Rear Body Harness Must be for a Hatch . I am also missing the small 2 inch pipe connecting the Top Water Neck to the Water Pump/Thermostat. I know this part can be found in the 4AC RWD also but i cant find any in the junk yards. Please help. Car is almost ready to drive im going cr...

Please help i need this harness.

Only Need a couple more parts to get my Ride on the road please help.

Rear Boyd Harness or Floor Harness whatever its called and brake switch for the brake lights.

Still looking please help. I only need the harness and switch

Still In Need of Parts Please Help.

Hatch Kouki Floor Harness Anybody?

Still looking.

Almost there Keep the Parts coming.

Need parts please help

GTS Hatch Rear Kouki Harness & 4age RWD GTS Alternator Bracket. Looking for GTS Hatch Rear Kouki taillight Harness and Fuel pump wire. I ALso need 4age Rwd GTS Alternator Bracket or mount. Alternator Bracket Call text email. 505-659-2465 or alvarado.e09@gmail.com Im very interested in these par...

Still Need Parts Please Help.

GTS Hatch Kouki, Rear Body Harness, Floor Harness & Taillight Brake Switch Looking for GTS Hatch Kouki Rear Body Harness, Floor Harness Im not sure of the name of the harness. Rear Body Harness That Runs From the Front to the taillights, fuel pump, rear speakers etc I ALso need Taillight Brake S...