???

No TRD shifter???

It an t50 oem shifter

Yeah hes a busy guy, he makes the bars at night after full time job .

TRD Spark Plugs wires. SOLD!!

Thx!!

Messaged.... pending

Bump... sniff sniff

Bummpp.....

post a sound clip after you get that new exhaust, been thinking of doing the same set up.

its still available, but it has now rusted i left it out should be able to resurface it at a shop

Bumpppp. .......

That’s awesome man , whoops thats right totally forgot about that timing cover lol after acouple time you can finesse it in but it is tight. 8-) Same thing goes with the rear coolant neck , If you remove the egr and tubes theres more room to Get it off and remove the rubber coolant hose By bottom of...

Btw theres a difference in Zenki and Kouki for side moldings.
Zenki a bit wider

Kouki a bit thinner

Looking for a zenki levin bumper near or around socal area or SD


Lmk

310-892-6260

Found!!

Thanks there still a few real corollas owners in SoCal!

My wiper motor, is going out slowly

Wanna get a replacement, new or used
Hopefully in working condition,

Thanks

Location??

T3 & battle garage both sell door hinges brand new!

It feels good to have a fresh pair, then to deal with used ones,

I had no cat, a Buddy club Spec II,Rsr mag. II and right now DD Trust

All pretty loud , if you daily you car just get a vibrant res n muffler n no Cat,

Ive seen some pretty low cars there, mine is definitely not the lowest but still ive taken my AE86 & camery it made it no problem, Corolla or not its a fun event just to experience


Btw

Heres a video i found , if theres any more ill post them


https://youtu.be/gZQ_2iyBGx0

Drive with nosie canceling Headphone cause that dam straight pipe is wayy to loud for the freeway

Lol

It is mostly , That newer and newer generations dont want to work on cars or put the time and effort to craft something, thats the trend in all of retail and services if you looks at different market its the same. For example new CVT transmissions they are design to be non-Serviceable for the ease a...

Pretty cool coverage of this event , if you have havent been , this event has been going on for last 3yrs or so
Usually All night long.

https://www.drivingline.com/articles/su ... i-gallery/

JDM spoiler Sold
brake Heat Shield Sold

Thanks again

Bump!

You still have tanabe sway bars??

Bumpp!!!

Also have 14in Oem pizza cutter rims $20each. 5rims

To put the big port injectors i need to re-solder the bigport injectors clips first.. for low res.

Plugs are dry, brown/normal, no white fouling
Idle , wideband 12.5-14

Exhaust smells normal , no fuel smell

I havent check the dipstick smell..

Yes bigport AFM, & Yeah i have the Resistor pack jumped to allow the hi Res. Injectors , i was thinking is it possible that at high RPM the SP injector is not responding to bigport ECU signal or injector pulse speed. And also cause high CR result of trd head gasket and also 4-1 headers but maybe...

:lol: Right on the nail. Hahah rebuilt smallport engine ,20v rod n crank, 0.5+ pistons,small port intake, Smallport,injectors 250cc,40psi @rail But on all Largeport electronics , i know its crippling I have a Wideband getting full lean at 1/2 -Wot , It runs good, at idle, At this point im trying to ...

Jondee

does the injector pusle fire more rapid at Higher RPM/load ?? That would allow more fuel to enter or is the
The Rate of injector pulse is constant and all levels of RPM.

Does the injector pulse differentiate between High comp ECU & Large port early model ECU USDM??

There is a factory high compression piston with 18mm wrist

If want help sourcing it lmk but only if your serious

Head work! Doo head work! Lol