Racecar: ITA AE86 with provenance(history)

User avatar
Kitsunami
Club4AG Enthusiast
Posts: 100
Joined: Thu May 05, 2016 11:36 am

Re: Racecar: ITA AE86 with provenance(history)

Postby Kitsunami » Tue Nov 28, 2017 7:27 pm

oldeskewltoy wrote:
oldeskewltoy wrote: there is no engine fan, mechanical driven or electric, has made me a bit uncomfortable. David (previous owner) said it wasn't a problem, after all this is a race car, it is used on track........

As this car's purpose has changed somewhat, besides the bits I've already mentioned, I'll be adding a thermo-switched electric fan to keep temps under control in less then perfect racing conditions.




More to come....... :D


key part to getting the fan in, and operational is the proper parts. Below is a coolant inlet for an AE82. This will bolt in as the stock one does, and is even pointing in the correct place. The original Toyota switch is grounded, and when hot it breaks the ground(opens) and the fan comes on. This works as a safety as well, if the switch breaks, the fan stays on.

Image

For Racecar I'm using a Honda switch, that will be open, and close @ temp (reverse of Toyota switch). This makes wiring the fan a bit simpler since the Honda switch is more conventional in operation.

BUT... the sensor doesn't quite fit. The hole for the probe is too narrow, and the threads aren't deep enough. So a few mods....

Image


and the Honda switch becomes right at home....

Image



with just enough of the sensor in the coolant to operate, yet not so far in that it seriously disrupts flow

Image



more to come..... :D


I'm getting ready to wire up my e-fan and would love a more simplified system. You should let me know how this works out, because I was thinking of doing the Toyota "normally closed" method initially.

Disable adblock

This site is supported by ads and donations.
If you see this text you are blocking our ads.
Please consider a Donation to support the site.


CloudStrife
Club4AG Pro
Posts: 628
Joined: Thu Oct 06, 2016 2:23 pm
Location: Middle of Hell, Florida

Re: Racecar: ITA AE86 with provenance(history)

Postby CloudStrife » Sat Dec 02, 2017 7:37 pm

So this car doesn't have traction brackets? Are they illegal in SCCA?

What is the deal with the rack? I don't see a reservoir, and didn't see a mention of it in the book. I highly doubt someone would "de-power" a rack in an official car..
Success guardian... Successsssssss..

User avatar
oldeskewltoy
Club4AG MASTER
Posts: 1792
Joined: Wed Jan 09, 2013 4:44 pm
Location: Portland, Oregon

Re: Racecar: ITA AE86 with provenance(history)

Postby oldeskewltoy » Sun Dec 03, 2017 12:00 pm

CloudStrife wrote:So this car doesn't have traction brackets? Are they illegal in SCCA?

What is the deal with the rack? I don't see a reservoir, and didn't see a mention of it in the book. I highly doubt someone would "de-power" a rack in an official car..


not illegal in SCCA... but illegal in the ITA division - think of it as a "stock" class. The car was always a non power steering car..... there are a few other "official anomalies" in THIS car..... :o some to be revealed ;)
OST Cyl head porting, - viewtopic.php?f=22&t=300

Building a great engine takes knowing the end... before you begin :ugeek:

Enjoy Life... its the only one you get!

CloudStrife
Club4AG Pro
Posts: 628
Joined: Thu Oct 06, 2016 2:23 pm
Location: Middle of Hell, Florida

Re: Racecar: ITA AE86 with provenance(history)

Postby CloudStrife » Sun Dec 03, 2017 12:08 pm

Wow! I've never seen a factory non-PS AE. I knew they existed but I figured they were all dead.

Thanks for shining light on ITA as well. I really want to enter either of the two, but I always worry I've modified the vehicle too much. Honestly ITA seems impossible for the (stock) 86.. But I'm sure someone is up to the challenge :)
Success guardian... Successsssssss..

Disable adblock

This site is supported by ads and donations.
If you see this text you are blocking our ads.
Please consider a Donation to support the site.


Gino1X1
Club4AG Enthusiast
Posts: 134
Joined: Wed Jun 05, 2013 10:59 am

Re: Racecar: ITA AE86 with provenance(history)

Postby Gino1X1 » Thu Dec 14, 2017 9:14 am

YoShImUrA wrote:A very stiff front sway bar and good enough rear compression stroke (comparatively soft springing too) will produce that effect


Alright thanx man. 8-)

User avatar
oldeskewltoy
Club4AG MASTER
Posts: 1792
Joined: Wed Jan 09, 2013 4:44 pm
Location: Portland, Oregon

Re: Racecar: ITA AE86 with provenance(history)

Postby oldeskewltoy » Mon Jan 15, 2018 5:18 pm

oldeskewltoy wrote:
current livery...

Image



The livery when built....

Image


I will most likely returning it to her original livery.......... ;)





almost there........ ;)

Image


still need to replicate a few pieces... but she is what she was...... ;)


more to come.... :mrgreen:
OST Cyl head porting, - viewtopic.php?f=22&t=300

Building a great engine takes knowing the end... before you begin :ugeek:

Enjoy Life... its the only one you get!

CloudStrife
Club4AG Pro
Posts: 628
Joined: Thu Oct 06, 2016 2:23 pm
Location: Middle of Hell, Florida

Re: Racecar: ITA AE86 with provenance(history)

Postby CloudStrife » Tue Jan 16, 2018 3:43 am

What wheels are those? Tom's? Borbet?

I have an impossible time finding 4x114.3 5 spoke "stars". They are my favorite.
Success guardian... Successsssssss..

User avatar
oldeskewltoy
Club4AG MASTER
Posts: 1792
Joined: Wed Jan 09, 2013 4:44 pm
Location: Portland, Oregon

Re: Racecar: ITA AE86 with provenance(history)

Postby oldeskewltoy » Wed Jan 17, 2018 7:18 am

CloudStrife wrote:What wheels are those? Tom's? Borbet?

I have an impossible time finding 4x114.3 5 spoke "stars". They are my favorite.


Revolution RFX wheels - http://www.revolutionwheels.com/
OST Cyl head porting, - viewtopic.php?f=22&t=300

Building a great engine takes knowing the end... before you begin :ugeek:

Enjoy Life... its the only one you get!

CloudStrife
Club4AG Pro
Posts: 628
Joined: Thu Oct 06, 2016 2:23 pm
Location: Middle of Hell, Florida

Re: Racecar: ITA AE86 with provenance(history)

Postby CloudStrife » Tue Feb 13, 2018 3:56 am

Hey oldeskewl,

I have another odd request. Is the A/C idler tension bracket still bolted on? If not, did it come with the purchase?

I have been desperately trying to find a factory manual rack AE88/86 with the tensioner bracket in place.

Ian
Success guardian... Successsssssss..

User avatar
oldeskewltoy
Club4AG MASTER
Posts: 1792
Joined: Wed Jan 09, 2013 4:44 pm
Location: Portland, Oregon

Re: Racecar: ITA AE86 with provenance(history)

Postby oldeskewltoy » Tue Feb 13, 2018 7:39 am

CloudStrife wrote:Hey oldeskewl,

I have another odd request. Is the A/C idler tension bracket still bolted on? If not, did it come with the purchase?

I have been desperately trying to find a factory manual rack AE88/86 with the tensioner bracket in place.

Ian


right now it has a Nevo crank pulley, alt and water pump.

I did get extra parts... but still not fully inventoried
OST Cyl head porting, - viewtopic.php?f=22&t=300

Building a great engine takes knowing the end... before you begin :ugeek:

Enjoy Life... its the only one you get!

Disable adblock

This site is supported by ads and donations.
If you see this text you are blocking our ads.
Please consider a Donation to support the site.



Return to “OWNERS and BUILDERS”

Who is online

Users browsing this forum: No registered users and 2 guests