Short stroke shocks front and rears alternatives.

notnilc20
Club4AG Expert
Posts: 397
Joined: Sun Dec 27, 2015 7:56 pm
Location: Memphis

Short stroke shocks front and rears alternatives.

Postby notnilc20 » Wed Jun 21, 2017 9:23 pm

I've been doing some research on alternative shocks to use for this short shock conversions....what i've found is that people have used:
Fronts) kyb agx rear shocks from an mr2 part number 765016
Or. Kyb agx front shocks from an mr2 part number 765015 (slightly longer than the 765016) works with a 40mm cutout from oem shock housing plus a 20mm spacer at the bottom of shock housing.

Rears) kyb agx rear shocks from a fbody camaro/firebird. Part number 743019

Why cut 40mm out and put back 20mm with a spacer? Would cutting only 20mm out give same result?
Are there any other alternatives. If you have done this mod, how was it and are you happy with it? Thanks.

Disable adblock

This site is supported by ads and donations.
If you see this text you are blocking our ads.
Please consider a Donation to support the site.


User avatar
jondee86
Moderator
Posts: 2026
Joined: Fri Jan 11, 2013 10:21 pm
Location: Wellington, New Zealand

Re: Short stroke shocks front and rears alternatives.

Postby jondee86 » Thu Jun 22, 2017 12:36 am

Have a read of this informative thread :)

viewtopic.php?t=7395

Cheers... jondee86
Give a person a fish, they eat for a day. Suggest they search before posting, and they learn a skill for a lifetime.

notnilc20
Club4AG Expert
Posts: 397
Joined: Sun Dec 27, 2015 7:56 pm
Location: Memphis

Re: Short stroke shocks front and rears alternatives.

Postby notnilc20 » Thu Jun 22, 2017 7:28 am

jondee86 wrote:Have a read of this informative thread :)

http://club4ag.com/forums/viewtopic.php?t=7395

Cheers... jondee86


Thanks Jondee86....yeah I actually ran across that thread after I posted this one....even still there was some confusion on there. But it looks like you cleared things up finally towards the end. So I'm going to go with;

Front) kyb agx p/n 765015 front shocks for a sw20 mr2. Cut out 40mm from shock housing and use 20mm spacer (can use stacked washers?) On the bottom of the shock.

Rear) kyb agx p/n 743019 rear shocks for a fbody camaro/firebird.

Springs i'm going to use t3 weld on kit for front and bc racing rear height adjuster (high/low kit) with bc racing springs for rear. If you see anything wrong with this set up let me know.....thanks.

User avatar
chohdog
Club4AG Enthusiast
Posts: 143
Joined: Thu Jan 10, 2013 10:15 pm

Re: Short stroke shocks front and rears alternatives.

Postby chohdog » Thu Jun 22, 2017 11:36 am

AGX...while used for many years are very undesirable in both their valving and durability. They blow often, but are cheap to replace. If you need something just for your car to ride on sure, get them. For your money however, I would recommend the Bilstein kit that T3 sells. Honestly, you get what you pay for with suspension and while the AGX are cheaper, the Bilsteins are much better.

Disable adblock

This site is supported by ads and donations.
If you see this text you are blocking our ads.
Please consider a Donation to support the site.


User avatar
jondee86
Moderator
Posts: 2026
Joined: Fri Jan 11, 2013 10:21 pm
Location: Wellington, New Zealand

Re: Short stroke shocks front and rears alternatives.

Postby jondee86 » Thu Jun 22, 2017 2:45 pm

Yeah.... can't argue with that ^^^^. Shocks that are specifically valves for an AE86
are always going to out perform shocks valved for some other vehicle. That being said,
I run the AGX combo with both front and rears on the softest setting with 3/2.8kg/mm
springs, and the ride is comfortable like stock. Cranking the rebound up just makes
the car "bouncy". I would guess that the shocks might work better with stiffer springs,
and if I can ever find some decent springs around 5/4kg/mm I'll give it a try.

Cheers... jondee86
Give a person a fish, they eat for a day. Suggest they search before posting, and they learn a skill for a lifetime.

User avatar
jondee86
Moderator
Posts: 2026
Joined: Fri Jan 11, 2013 10:21 pm
Location: Wellington, New Zealand

Re: Short stroke shocks front and rears alternatives.

Postby jondee86 » Sat Jun 24, 2017 10:57 pm

Just while on the subject of using shocks not specifically valved for the AE86,
I have decided to try an experiment. Since I already have some new in the box
Koni 8641-1146SPORT inserts for an AE92 that will work on the front of an AE86,
I am going to get some of the 8041-1186SPORT Mustang rears. Then I will have
top adjustable shocks front and rear :)

Opinion on the Mustang shocks seems to be about equally split between I think
it should work
and the usual they will be crap because they are valved for
a heavier vehicle
.

Time to settle the matter !! And also to see if there really is that much difference
between the AGX combo and the Koni sports.

Cheers... jondee86
Give a person a fish, they eat for a day. Suggest they search before posting, and they learn a skill for a lifetime.

notnilc20
Club4AG Expert
Posts: 397
Joined: Sun Dec 27, 2015 7:56 pm
Location: Memphis

Re: Short stroke shocks front and rears alternatives.

Postby notnilc20 » Sun Jun 25, 2017 7:14 am

jondee86 wrote:Just while on the subject of using shocks not specifically valved for the AE86,
I have decided to try an experiment. Since I already have some new in the box
Koni 8641-1146SPORT inserts for an AE92 that will work on the front of an AE86,
I am going to get some of the 8041-1186SPORT Mustang rears. Then I will have
top adjustable shocks front and rear :)

Opinion on the Mustang shocks seems to be about equally split between I think
it should work
and the usual they will be crap because they are valved for
a heavier vehicle
.

Time to settle the matter !! And also to see if there really is that much difference
between the AGX combo and the Koni sports.

Cheers... jondee86


I'm definantly interested in seeing/hearing about the results....keep us in the loop. Thanks.

Deuce Cam
Posts: 1275
Joined: Sun Jan 13, 2013 2:41 pm
Location: AZ

Re: Short stroke shocks front and rears alternatives.

Postby Deuce Cam » Wed Jun 28, 2017 6:42 pm

Shortening the strut basically helps set the shock height and ride height.

A 20 mm spacer is used on really short stroke/length inserts to set the shock at a height where its in an ideal usable range at static ride height. The agx that people use actually wouldnt fit in a 40 mm cut strut with a 20 mm spacer, for reference.

notnilc20
Club4AG Expert
Posts: 397
Joined: Sun Dec 27, 2015 7:56 pm
Location: Memphis

Re: Short stroke shocks front and rears alternatives.

Postby notnilc20 » Thu Jun 29, 2017 7:19 am

Deuce Cam wrote:Shortening the strut basically helps set the shock height and ride height.

A 20 mm spacer is used on really short stroke/length inserts to set the shock at a height where its in an ideal usable range at static ride height. The agx that people use actually wouldnt fit in a 40 mm cut strut with a 20 mm spacer, for reference.


Ok so, i ordered some front agx for an sw20 mr2 to use in my ae86....you're saying that the 40mm cut with 20mm spacer will not work with this setup? Can someone who has these shocks tell me what should be cut and spaced for this shock to work? Thanks.

Deuce Cam
Posts: 1275
Joined: Sun Jan 13, 2013 2:41 pm
Location: AZ

Re: Short stroke shocks front and rears alternatives.

Postby Deuce Cam » Thu Jun 29, 2017 2:12 pm

You can use thoseninserts in a 40 mm cut strut, but you will only need roughly a 5 mm spacer below the strut insert to keep it captive in the strut. Its because the agx cartridge length is longer then on say... the trd/hts short stroke inserts.

notnilc20
Club4AG Expert
Posts: 397
Joined: Sun Dec 27, 2015 7:56 pm
Location: Memphis

Re: Short stroke shocks front and rears alternatives.

Postby notnilc20 » Thu Jun 29, 2017 4:26 pm

Deuce Cam wrote:You can use thoseninserts in a 40 mm cut strut, but you will only need roughly a 5 mm spacer below the strut insert to keep it captive in the strut. Its because the agx cartridge length is longer then on say... the trd/hts short stroke inserts.


Gotcha.....thanks a lot. :)

User avatar
jondee86
Moderator
Posts: 2026
Joined: Fri Jan 11, 2013 10:21 pm
Location: Wellington, New Zealand

Re: Short stroke shocks front and rears alternatives.

Postby jondee86 » Fri Jun 30, 2017 2:33 pm

The size of the spacer depends a lot on how you make the spacer, and on what you use
for the gland nut.

The bottom of the strut on the inside is not just flat. There is a big chamfer all the way
round, so if you get a washer that just fits inside the tube, it does not fall all the way to
the bottom. It sits on top of the chamfer so you lose about 10mm. I got some allow rod
about 20mm dia (from memory) that just fitted inside the ring on the bottom of the AGX
insert. Then I tapered one end to make it small enough to actually sit hard down on the
bottom of the strut.

For the gland nut I used the OEM one with the seal removed, and had the inside opened
out on a lathe so that it sat over and cupped the top of the insert. That gains about
10mm at the top. The end result was that my spacers did end up at 20mm. So you just
need to do a trial fit until you get the spacer right. So long as you have a couple of
threads still exposed when you tighten the gland nut down, you are good :)

Cheers... jondee86
Give a person a fish, they eat for a day. Suggest they search before posting, and they learn a skill for a lifetime.

notnilc20
Club4AG Expert
Posts: 397
Joined: Sun Dec 27, 2015 7:56 pm
Location: Memphis

Re: Short stroke shocks front and rears alternatives.

Postby notnilc20 » Sat Jul 01, 2017 7:16 am

jondee86 wrote:The size of the spacer depends a lot on how you make the spacer, and on what you use
for the gland nut.

The bottom of the strut on the inside is not just flat. There is a big chamfer all the way
round, so if you get a washer that just fits inside the tube, it does not fall all the way to
the bottom. It sits on top of the chamfer so you lose about 10mm. I got some allow rod
about 20mm dia (from memory) that just fitted inside the ring on the bottom of the AGX
insert. Then I tapered one end to make it small enough to actually sit hard down on the
bottom of the strut.

For the gland nut I used the OEM one with the seal removed, and had the inside opened
out on a lathe so that it sat over and cupped the top of the insert. That gains about
10mm at the top. The end result was that my spacers did end up at 20mm. So you just
need to do a trial fit until you get the spacer right. So long as you have a couple of
threads still exposed when you tighten the gland nut down, you are good :)

Cheers... jondee86


Wow.....sounds complicated...for as much as this is done on an 86 i'm surprised there isn't a write up or vid on this yet.

User avatar
jondee86
Moderator
Posts: 2026
Joined: Fri Jan 11, 2013 10:21 pm
Location: Wellington, New Zealand

Re: Short stroke shocks front and rears alternatives.

Postby jondee86 » Sat Jul 01, 2017 2:33 pm

jondee86 wrote:The size of the spacer depends a lot on how you make the spacer, and on what you use
for the gland nut.

The bottom of the strut on the inside is not just flat. There is a big chamfer all the way
round, so if you get a washer that just fits inside the tube, it does not fall all the way to
the bottom. It sits on top of the chamfer so you lose about 10mm. I got some alloy rod
about 20mm dia (from memory) that just fitted inside the ring on the bottom of the AGX
insert. Then I tapered one end to make it small enough to actually sit hard down on the
bottom of the strut.

For the gland nut I used the OEM one with the seal removed, and had the inside opened
out on a lathe so that it sat over and cupped the top of the insert. That gains about
10mm at the top. The end result was that my spacers did end up at 20mm. So you just
need to do a trial fit until you get the spacer right. So long as you have a couple of
threads still exposed when you tighten the gland nut down, you are good :)

Cheers... jondee86
Give a person a fish, they eat for a day. Suggest they search before posting, and they learn a skill for a lifetime.

User avatar
jondee86
Moderator
Posts: 2026
Joined: Fri Jan 11, 2013 10:21 pm
Location: Wellington, New Zealand

Re: Short stroke shocks front and rears alternatives.

Postby jondee86 » Sat Jul 01, 2017 2:56 pm

Nah... not cmplicated :) Once you have the strut and insert on the bench in front
of you it will all become clear. This is not my pic, but it shows how I had the OEM
gland nuts modified to fit the top of the inserts...

Image

You might not have to do that. You need to trial assemble the components then
do some measuring to see how much spacer is required to lift the insert up so that
you still have a couple of threads showing on the gland nut when it is tightened.

Cheers... jondee86
Give a person a fish, they eat for a day. Suggest they search before posting, and they learn a skill for a lifetime.

Deuce Cam
Posts: 1275
Joined: Sun Jan 13, 2013 2:41 pm
Location: AZ

Re: Short stroke shocks front and rears alternatives.

Postby Deuce Cam » Sun Jul 02, 2017 9:17 am

T3 would prob sell the spacers they use on their coilovers (stock 40 mm cut tube, agx strut) for prob like $10 bucks. They fit inside the 'button' on the bottom of the agx cartridge, and also the center of the chamfer on the strut tube. Iirc they were used with the oem gland nut
- without modding it - and the insert was held captive. (Going off memory from when i parted out a pair of their coilovers a few years ago.

notnilc20
Club4AG Expert
Posts: 397
Joined: Sun Dec 27, 2015 7:56 pm
Location: Memphis

Re: Short stroke shocks front and rears alternatives.

Postby notnilc20 » Sun Jul 02, 2017 7:41 pm

Great info guys....thanks a lot! I'll contact t3 tmrw and see about the spacers.

User avatar
jondee86
Moderator
Posts: 2026
Joined: Fri Jan 11, 2013 10:21 pm
Location: Wellington, New Zealand

Re: Short stroke shocks front and rears alternatives.

Postby jondee86 » Sun Jul 16, 2017 8:30 pm

jondee86 wrote:I am going to get some of the 8041-1186SPORT Mustang rears.

Have these now and while I won't be installing them for a while, I did put them
alongside some Toyota OEM long stroke KYB gas shocks for comparison.

The KONI's are about 2 inches shorter when fully extended. This is good.
The KONI's are about 2 inches longer when fully compressed. This may not be good.

The hole in the KYB bottom bush is 16mm dia.
The steel sleeve in the KONI bottom bush is 17mm dia. This may not be good.

The fact that the KONI is longer when fully compressed is most likely down to the
bumpstop they have on the spear. Subject to a bit of checking, it may be possible
to remove the bumpstop and gain 2 more inches of bump travel (if needed). A
simple solution for the bottom bush might be to press out the KONI bush and use
the bushes from the OEM shock. The steel outer sleeve looks to be roughly the
same diameter, so this should work.

I'll do a proper writeup when the springs arrive and I can install this stuff :)

Cheers... jondee86
Give a person a fish, they eat for a day. Suggest they search before posting, and they learn a skill for a lifetime.

Disable adblock

This site is supported by ads and donations.
If you see this text you are blocking our ads.
Please consider a Donation to support the site.



Return to “TECH: Corolla AE86”

Who is online

Users browsing this forum: Google [Bot] and 6 guests