Bump steer after aw11 manual rack conversion

Nomnom83
Club4AG Enthusiast
Posts: 64
Joined: Mon Jul 08, 2013 8:29 pm

Bump steer after aw11 manual rack conversion

Postby Nomnom83 » Wed Jun 29, 2016 10:10 pm

Installed and centered aw11 manual in my ae86, now have bump steer when hitting bumps on the passenger wheel. Anyone else have this issue?

Found this
http://forums.club4ag.com/zerothread?id=89702&page=2

But no one else talks about this.

Disable adblock

This site is supported by ads and donations.
If you see this text you are blocking our ads.
Please consider a Donation to support the site.


davew7
Club4AG Enthusiast
Posts: 129
Joined: Fri Jun 06, 2014 4:34 am
Location: Michigan

Re: Bump steer after aw11 manual rack conversion

Postby davew7 » Thu Jun 30, 2016 4:07 am

If you are "sure" that the inner tie rod pivots for LH/RH are equal distance, [not clamped in AW-11 factory location] then you will have to adjust the elevation at each pivot point to get ends of the tie rods traveling thru the same arc.
Get a suspension handling book that shows how to make a simple dump steering gauge, and plan on several hours making shims to get the minimum bump steer. You will find that an adjustment as small as .020" will change the steering. You can also adjust the fore/aft location of the rack, but that will also affect Ackermann. Dave W

Deuce Cam
Posts: 1306
Joined: Sun Jan 13, 2013 2:41 pm
Location: AZ

Re: Bump steer after aw11 manual rack conversion

Postby Deuce Cam » Thu Jun 30, 2016 2:02 pm

I remember the thread/pic you linked and it's the only place I've seen the comparison. I asked around a lot over the years and nobody seems to know for sure if they are different.

User avatar
ToeKnee805
Club4AG Expert
Posts: 299
Joined: Wed Jan 09, 2013 8:17 pm
Location: Southern California, 805

Re: Bump steer after aw11 manual rack conversion

Postby ToeKnee805 » Thu Jul 07, 2016 12:53 am

track driving i felt like the ae86 rack was harder to turn than an aw11 rack, but as far as bump steer, do you have RCAs already? Maybe converting to manual just made the bumpsteer that was already there more noticeable?
1986 Corolla GT-S -- Unmolested -- Now Resto Project
1985 Corolla GT-S -- Turbo Levin Track Car
1982 Corolla 1.8 -- Sitting collecting dust

Disable adblock

This site is supported by ads and donations.
If you see this text you are blocking our ads.
Please consider a Donation to support the site.


Deuce Cam
Posts: 1306
Joined: Sun Jan 13, 2013 2:41 pm
Location: AZ

Re: Bump steer after aw11 manual rack conversion

Postby Deuce Cam » Tue Jul 12, 2016 11:47 am

I just came across this pic in badboy88000's build thread (ae86 top, aw11 bottom):

Image

The ae86 housing definitely is shorter. I wonder if the rack/gear is the same length since it's hard to tell in the pic.

Also, here's the pic from Grant's old build thread that the op linked (ae86 on top, aw11 bottom):

Image

assassin10000
Club4AG Enthusiast
Posts: 130
Joined: Thu Jan 10, 2013 10:07 pm

Re: Bump steer after aw11 manual rack conversion

Postby assassin10000 » Thu Aug 04, 2016 2:11 pm

Yeah, both housings are different lengths. Aw11 internal gear is about 1/8" longer than ae86.

Andrew

Deuce Cam
Posts: 1306
Joined: Sun Jan 13, 2013 2:41 pm
Location: AZ

Re: Bump steer after aw11 manual rack conversion

Postby Deuce Cam » Thu Aug 04, 2016 3:33 pm

Assuming the r&p are interchangeable... the quaife aw11 r&p (or stock aw11) in an ae86 housing might be ideal.

I wonder how the ae71 stuff compares.

Deuce Cam
Posts: 1306
Joined: Sun Jan 13, 2013 2:41 pm
Location: AZ

Re: Bump steer after aw11 manual rack conversion

Postby Deuce Cam » Sat Sep 16, 2017 2:37 pm

So an opportunity presented itself to measure an ae86 rack/housing and an aw11 rack/housing.

The housing AND rack are different lengths when comparing the ae86, and aw11 parts. I used a measuring tape with the racks both installed on different cars, so the measurements aren't exactly precise, but anyway here goes:

ae86
rack: 21-11/16"
housing: 15-3/4"

aw11
rack: 21-7/8"
housing: 16-3/8"

The aw11 housing is 5/8" longer than ae86. The distance between the middle of the driver side mounting point and the end of the driver side rack housing is the same on both. This means the extra 5/8" length on the aw11 housing all ends up on the passenger side when installed in an ae86. In other words, an aw11 rack housing is off center when installed in an ae86.

It's also interesting to note that the ae86 rack length (part that inner tie rods bolt to) is 3/16" shorter compared to the aw11 rack. The increased length equates to higher steering ratio AND steering angle/travel. Think of the added length like a rack spacer which also adds more angle/travel.

For reference I also found this old link: http://www.ae86drivingclub.com.au/forum ... -2778.html

The most important post from the linked thread above is quoted below for convenience:

2nd March 2009, 08:28 PM
Note: still looking for info if you have it, but below is what I think from limited info, but cafefull measuring and calculating of what I do have:


All manual racks (except aftermarket quick racks) use the same pinion (6 teeth) and gear ratio. (About 43.3mm rack movement per turn). All rack housings (at least the manuals) are of the same width, 400mm +-1mm.

AE86/AE85 with power steer
rack width: 530mm?
stroke: 130mm
turns: 3

AE86/AE85 with manual steer
rack width: 552mm
stroke: 152mm
turns: 3.5

AE86 GTV manual
rack width: 530mm
stroke: 130mm
turns: 3

The GTV has the same steering rack ratio, but the resulting steering is quicker only due to the shorter power steering knuckles. Due to the sharper angle the PS knuckles would give, the GTV rack stroke is limited. Both the regular manual cars and the GTV would have similar maximum steering angle.

KE70/AE71 some* manual
rack width: 545mm
stroke: 144mm
turns: 3.3

*The KE70 in Australia shares the same rack housing as the AE86 (400mm wide) and the same pinion and gear ratio, but the rack itself is not as long. Some KE70's in other countrys use the same rack as the AE86.

To achive the sharpest steering angle with the above parts, we use the longer 152mm steering rack (not the GTV one), combined with the PS/GTV knuckles. At this point, the tyre may start to rub on the inner body. To achive even greater steering angle (with either **longer rack, special rack ends, slip on spacers or screw on spacers) you also need longer lower control arms.

Tie-rod ends:
AE86 steering rod ends are about 190-195mm long, from ball joint centre to end. Due to a narrower rack, the GTV ones are about 208mm long. With longer lower control arms, use RA40/KE30 tie-rods.

Quick racks from TRD, Cusco/Chowini and Quaife are all based on the normal 152mm stroke manual rack. The Quaife one is still available, and has 2.5 turns.

**If you want a custom length rack, you can use a RA60 one and cut it down.
Kid Karola


The specs listed in the above quote for ae86 are in line with my measurement.

Deuce Cam
Posts: 1306
Joined: Sun Jan 13, 2013 2:41 pm
Location: AZ

Re: Bump steer after aw11 manual rack conversion

Postby Deuce Cam » Thu Sep 21, 2017 12:20 pm

Also reached out to quaife regarding their qsr kits for ae86 and aw11. Both kits use the same exact rack. Only the pinions differ. Both racks are 21.653" long, which is even shorter than an oem ae86 manual rack

xslowpokex
Club4AG Enthusiast
Posts: 133
Joined: Fri Jun 07, 2013 12:20 pm

Re: Bump steer after aw11 manual rack conversion

Postby xslowpokex » Fri Sep 22, 2017 4:32 am

If your 86 is lowered more than 1.5inches from stock you will need front RCAs to alleviate the bump steer, if you have RCAs and your bump steer is still persistent then your car is too lowered. You have 3 option, go back to powered steering, raise your car up, or just live with it. I honestly think manual steering is more adequate in a track or weekend car its very inconvenient for daily driving especially in tight spaces, like parking lots, parallel parking, moving in slow traffic, its just a work out period lol and if not done right can actually make the steering feel crappy leaving you with too much steering slack to sort out. But deleting the power steering does make for more noticeably rev happy 4ag : )

User avatar
BattleGarage_RS
Club4AG Enthusiast
Posts: 148
Joined: Sun Jan 13, 2013 3:15 pm

Re: Bump steer after aw11 manual rack conversion

Postby BattleGarage_RS » Fri Sep 22, 2017 1:46 pm

I strongly urge people to find a true manual rack because of the bump steer we noticed with the AW11 racks when properly centering the rack.

Your choices with the AW11 rack seem to be 1. Have too much angle turning left 2. Having equal steering angle but worse bump steer on oneside than the other.

Also, hit up Ezekiel for a proper P/S rack de-power service. I have driven his car multiple times with his properly de-powered rack and it feels GOOD!

Grant
The tuning spirit of the 90's is alive again!

AE86 parts 24/7 :arrow: http://shop.battlegarage-rs.com

Deuce Cam
Posts: 1306
Joined: Sun Jan 13, 2013 2:41 pm
Location: AZ

Re: Bump steer after aw11 manual rack conversion

Postby Deuce Cam » Fri Sep 22, 2017 3:29 pm

^exactly. Equal steering from center (lock-to-lock) when using an aw11 rack in an ae86 equates to different overall tie rod lengths (inner pivot to outer pivot) on each side, which causes the alignment/bump steer issues.

zokustyle
Club4AG Regular
Posts: 34
Joined: Sat Feb 23, 2013 3:18 pm

Re: Bump steer after aw11 manual rack conversion

Postby zokustyle » Wed Nov 15, 2017 12:48 pm

Other than finding a factory manual steering at a junkyard (impossible now?), where are we supposed to find an AE86 manual rack? Everyone has discontinued their remans.

GZE_RA21
Club4AG Enthusiast
Posts: 99
Joined: Sat Jan 16, 2016 6:19 pm
Location: San Clemente, California
Contact:

Re: Bump steer after aw11 manual rack conversion

Postby GZE_RA21 » Tue Nov 21, 2017 3:14 pm

^^^^Have you tried rockauto.com? Last I checked they still had manual racks.


*edit just checked, they are in fact out of stock currently. :(

Disable adblock

This site is supported by ads and donations.
If you see this text you are blocking our ads.
Please consider a Donation to support the site.



Return to “TECH: Corolla AE86”

Who is online

Users browsing this forum: Bing [Bot] and 10 guests