Aukword1's Beams Swapped AE86

aukword1
Club4AG Expert
Posts: 306
Joined: Fri Dec 06, 2013 6:03 pm

Aukword1's Beams Swapped AE86

Postby aukword1 » Sat Sep 23, 2017 6:30 pm

Okay well finally decided to start a build thread even though I've already done so much building already. A little background on the car first.

The car was purchased from my brother-in-law back in 2011 and was basically just a rusted rolling chasis that sat in the Santa Cruz mountains constantly getting rained on. I towed it back to Southern California to begin a lot of restoration. After several weeks with a wire wheel, filler and paint I restored the interior to a nice matte black finish.

Now I was ready to address the elephant in the room. I had no bumpers, no fenders, no headlights, no interior and no engine!. I bought all of these parts over the course of a few months and installed them. I went with a 4agze engine and converted it to a regular 4age and put on an HKS supercharger that I got from Japan. S/C seized on the dyno so I decided to go turbo. The car was turbo ever since and I painted the exterior and lined the interior with T3's custom panels. Then recently I overhauled the old **** suspension and put in mostly T3 suspension parts and arms. Upgraded the front brakes to wilwoods and running about 1" spacers all around. Car sits nice and drives well.

Here are some old pics I could dig up of the car.

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Here is how it currently sits.

Image

Now begins the new build.

Image

Car is on its way to my family's house to get the infamous 3sge Beams swap. I decided to start this thread because there isn't much info about doing a beams swap on an AE86. There is some info and a lot of parts but nothing really covers the whole process. Current parts list purchased so far is:

3sge Beams w/ J160 Trans and OEM ECU- around $1300
Xcessive Manufacturing one piece driveshaft - $385
JSP Fab Beams Mount Kit - $585
JSP Fab Shifter Relocator Kit - $365
SQ Engineering Slimline rear housing - about $150 from Battle Garage
SQ Engineering Slimline alternator brack - about $150 from Battle Garage
Koyorad Beams Swap Radiator - $270

More to come soon!

Disable adblock

This site is supported by ads and donations.
If you see this text you are blocking our ads.
Please consider a Donation to support the site.


CloudStrife
Club4AG Expert
Posts: 300
Joined: Thu Oct 06, 2016 2:23 pm

Re: Aukword1's Beams Swapped AE86

Postby CloudStrife » Sun Sep 24, 2017 1:02 am

a Beam's swap eh?

MAY THE LORD BE WITH YOU AND YOUR CHECKING ACCT.

No but really, what's the allure of that motor? What do they come out of?

aukword1
Club4AG Expert
Posts: 306
Joined: Fri Dec 06, 2013 6:03 pm

Re: Aukword1's Beams Swapped AE86

Postby aukword1 » Sun Sep 24, 2017 6:56 am

They come out of Toyota Altezza RS200's, we never got them in the states though. The allure is having a modern engine and gearbox and having a better torque curve. The HP and Torque curve are supposedly pretty similar to the F20c motors but get to keep it in the Toyota family.

CloudStrife
Club4AG Expert
Posts: 300
Joined: Thu Oct 06, 2016 2:23 pm

Re: Aukword1's Beams Swapped AE86

Postby CloudStrife » Sun Sep 24, 2017 11:28 am

Huh, no ****. I had no idea JDM altezzas got those. If it's similar to the F20c then it sounds awesome, but my **** man, you are at $3,200 already lol.

Disable adblock

This site is supported by ads and donations.
If you see this text you are blocking our ads.
Please consider a Donation to support the site.


aukword1
Club4AG Expert
Posts: 306
Joined: Fri Dec 06, 2013 6:03 pm

Re: Aukword1's Beams Swapped AE86

Postby aukword1 » Mon Sep 25, 2017 7:43 am

I know :cry:, It definitely isn't the cheapest swap. Hopefully I can sell my current drivetrain and ECU to cover some of the costs though.

jinx
Club4AG Enthusiast
Posts: 195
Joined: Fri Jan 11, 2013 10:20 pm

Re: Aukword1's Beams Swapped AE86

Postby jinx » Mon Sep 25, 2017 8:01 am

what happened with the turbo setup ? Even the mildest of 4AGTEs should leave a BEAMs in the dust :roll:

CloudStrife
Club4AG Expert
Posts: 300
Joined: Thu Oct 06, 2016 2:23 pm

Re: Aukword1's Beams Swapped AE86

Postby CloudStrife » Mon Sep 25, 2017 2:09 pm

I agree, but he needs more positive :)

Here you go bro
https://www.youtube.com/watch?v=NiEzZWhHTEM

I guess a good thing is 3SGE parts are pretty easy to come buy minus BEAMs specific stuff...

aukword1
Club4AG Expert
Posts: 306
Joined: Fri Dec 06, 2013 6:03 pm

Re: Aukword1's Beams Swapped AE86

Postby aukword1 » Mon Sep 25, 2017 5:45 pm

The turbo setup is fine and honestly it was a lot of fun to drive. I really just wanted to try something new. I think it will be a fun learning experience and if I don't like it, I have two 4AG motors sitting in my garage still lol.

User avatar
Jayrdee
Club4AG Enthusiast
Posts: 162
Joined: Tue Mar 21, 2017 8:25 am
Location: Lexington KY
Contact:

Re: Aukword1's Beams Swapped AE86

Postby Jayrdee » Tue Sep 26, 2017 11:55 am

Subscribed. This will be so sick.
[Another Day, Another Beer]
_____________________
instagram: @JacobDurbin

aukword1
Club4AG Expert
Posts: 306
Joined: Fri Dec 06, 2013 6:03 pm

Re: Aukword1's Beams Swapped AE86

Postby aukword1 » Wed Sep 27, 2017 8:19 am

Small update of what I did over the past weekend.

Image
Pulled the old engine out. I think I will paint the engine bay back to white after cleaning it up this coming weekend.

Image
Here is the old engine on the stand.

Image
An awkwardly taken photo of the side of the old engine. Yes I know the Kanji is upside down. I blame my wife for that.

Image
Tial ABV ;)

Image
Here is the Beams engines waiting to be installed.

Image
A lonely T50 hanging out by an old 4age

I'm still waiting on the mount kit from JSP fab so I don't know if I will be able to do much this weekend besides cleaning up the engine bay, pulling wiring harnesses, and prepping for paint. I don't want to paint it until after I hammer the firewall and transmission tunnel so i need to figure out clearances first. Will update soon though!

aukword1
Club4AG Expert
Posts: 306
Joined: Fri Dec 06, 2013 6:03 pm

Re: Aukword1's Beams Swapped AE86

Postby aukword1 » Tue Oct 03, 2017 5:38 pm

Small update. Pulled everything out of the engine bay and put a fresh coast of paint on it.

Image

John informed me today that he would be shipping the motor mounts and shifter kit. Hopefully get them by Saturday so it gives me something to do this weekend lol.

CloudStrife
Club4AG Expert
Posts: 300
Joined: Thu Oct 06, 2016 2:23 pm

Re: Aukword1's Beams Swapped AE86

Postby CloudStrife » Tue Oct 03, 2017 7:28 pm

Where are you again bro? I'd learn so much if I helped! aha

aukword1
Club4AG Expert
Posts: 306
Joined: Fri Dec 06, 2013 6:03 pm

Re: Aukword1's Beams Swapped AE86

Postby aukword1 » Tue Oct 03, 2017 8:48 pm

Orange County, California. I am still learning myself sometimes but I could I always use an extra hand lol

aukword1
Club4AG Expert
Posts: 306
Joined: Fri Dec 06, 2013 6:03 pm

Re: Aukword1's Beams Swapped AE86

Postby aukword1 » Sun Oct 08, 2017 5:13 pm

Got the mount kit from jspfab today.

This is how the engine will sit from now on. I know I didn't have to cut the core support but I did and it made it a lot easier to get in and out.
Image

Here are the 1" subframe spacers installed that came with the kit. Pretty easy to get in. Just unbolt them along with the camber plates and jack up the frame.
Image

One thing they don't tell you about this swap is that they use the original AE86 motor mounts. Saved me some money there. The JSP motor mounts are well made and easy to install. Highly recommend John's work!
Image

Tomorrow I will bolt up the tranny mount and the driveshaft. Probably going to have to beat the transmission tunnel. One other thing I'd like to add, if you have a manual rack installed prior to the swap, you are going to have to pull the intermediate shaft out about half an inch for it to fit with the subframe being dropped an inch. I have yet to do this so I will probably tackle that after the transmission is bolted up.

aukword1
Club4AG Expert
Posts: 306
Joined: Fri Dec 06, 2013 6:03 pm

Re: Aukword1's Beams Swapped AE86

Postby aukword1 » Mon Oct 09, 2017 4:37 pm

Last update for a couple weeks.

Got the Transmission bolted in. Really, the only hammering of the transmission tunnel I had to do was by the shifter. On the spot between the hand brake and the shifter, I had to hammer it up for the shifter to clear the tunnel. After that it was smooth sailing.

Image

Driveshaft bolted up, pretty basic stuff, nothing special. Courtesy of Xccessivemanufacturing.
Image

Another pic of the driveshaft bolted in. The exhaust will probably be the last thing I do.
Image

Here is a picture of the shifter relocation kit by JSPfab.
Image

Another pic of the shifter. You can see where I had to bash it between the shifter and hand brake.
Image

Last thing I did today was pull the intermediate shaft out about an inch and then re-attached the steering column. Nothing special there.

Next update will be in two weeks. I wont be able to work on it next weekend due to having to help my sister move. The plans for that update will include, adding a steel braided clutch line to bolt into the J160 slave cylinder, re-attaching the core support along with the koyorad radiator, and possibly making a template and welding up the headers to wrap around the steering column. After that begins the fun part, wiring.

aukword1
Club4AG Expert
Posts: 306
Joined: Fri Dec 06, 2013 6:03 pm

Re: Aukword1's Beams Swapped AE86

Postby aukword1 » Sat Oct 21, 2017 6:08 pm

Small half weekend update.

Here is my temporary attempt at headers.

Image

I re-attached the core support.

Image

Also, I painted the bottom windshield cover and those vents that attach under it by the windshield wipers. I added the SS braided clutch line and linked it to the j160 slave to see if that works. I have yet to add fluids though. It looks like the original slave cylinder will fit but I want to see which combination will work. Tomorrow I will finish the temporary headers and put most of the body panels back on, then tow it back home for the remainder of the work. Also, I will wrap the headers and paint the core support again since it got scratched. Will update tomorrow with more pics!

aukword1
Club4AG Expert
Posts: 306
Joined: Fri Dec 06, 2013 6:03 pm

Re: Aukword1's Beams Swapped AE86

Postby aukword1 » Sun Oct 22, 2017 7:57 pm

Alright, So I finished painting some parts.

Image

Also, I finished the headers and got them hooked up to the exhaust. By far this was the most difficult part of the whole swap so far. Parts for the header costed about $200 just for the bent steel needed and a 4-1 collector. I hope I never have to do something like this again, it was extremely difficult without a template and just a mig welder. It was basically just all guess work lol. This is just a temporary fix until I can get some legit headers and some nice exhaust work done to the car but it should work for the time being.
Image

I re-painted the core support along with some other spots in the engine bay that were missed. Now I just have to put on the headlights, fenders, bumper and hood then I can bring it home to install the radiator and add all the fluids etc...Then all that is left is the wiring!

Disable adblock

This site is supported by ads and donations.
If you see this text you are blocking our ads.
Please consider a Donation to support the site.



Return to “OWNERS and BUILDERS”

Who is online

Users browsing this forum: No registered users and 3 guests