Page 1 of 1

wood shift knob to match your wood steering wheel

Posted: Tue Feb 26, 2013 4:47 pm
by marley4us
New to me Nardi wood steering wheel! sexy, ohhh yeah. So lets make a shift knob to match!!!!
Image

Go buy a block of wood, some stain, have a drill and some expoxi and nutts that match the thread pitch of your car.

Block oh wood, going to make me a wood shifter too!
Image

Got this far, smoothing it out... I wanted to keep working, but I could tell I was pissing off my neighbors
Image

Man I have not widdled since grade school, when we would go camping.... man I forgot how fun it is!

Image

Image

Finished smoothing it out. Purchased Stain, and Polyurethane clear gloss sealer, and nuts to mount inside the shifter.
Image

Image

First layer of stain
Image

second layer of stain
Image
Image

Third layer of stain
Image

I am waiting to see how dark this layer turns, and if it will match the wheel or I need another layer. In the morning I will add the clear gloss, with lots of layers for durability and a shinny finish!

Clear coat, here is the first few coats, use gentle strokes so you dont get air bubbles messing up the finish
Image

Image

Image

Image
Image

Finished the shifter, and I have to save I am pretty darn proud! It could use some wetsanding to smooth out the many coats of clear. but other then that perfections side man I can not believe I hand made this!
Image

Image

Image

And it matches my wheel pretty good! Not bad for pilfering left over wood from my Halloween costume stilts lol!
Image

Got wood
Image

Image

Re: wood shift knob to match your wood steering wheel

Posted: Fri Jan 31, 2014 6:29 pm
by marley4us
Thanks, I would love to see yours too! maybe even buy some of your work!


Started on this Ebrake handle

buy wood
Image
20140129_141704 by marley4us1985, on Flickr



cut wood
Image
20140129_142035 by marley4us1985, on Flickr

Sand the handle to your liking
Image
20140129_141726 by marley4us1985, on Flickr

Notch the grip
Image
20140129_143449 by marley4us1985, on Flickr

Hand sand out the burn marks
Image
20140129_143725 by marley4us1985, on Flickr



Gloss
Image
20140129_150303 by marley4us1985, on Flickr


put gloss on it
Image
20140129_151306 by marley4us1985, on Flickr

Re: wood shift knob to match your wood steering wheel

Posted: Tue Feb 18, 2014 4:09 pm
by marley4us
F*%K getting the ebrake handle of was a HUGE PITA! It did not want to budge, ended up cutting it down the center to remove it lol!

Image
20140218_130407 by marley4us1985, on Flickr

Image
20140218_130413 by marley4us1985, on Flickr

So I wanted to make a push button for my wooden ebrake handle.

took a 11/16 bit to drill the hole for the ebrake to slip on

Image
20140218_130430 by marley4us1985, on Flickr


Hole drilled
Image
20140218_130436 by marley4us1985, on Flickr

and a 5/8 for the button
Image
20140218_130826 by marley4us1985, on Flickr

got a slighter larger rod then the 5/8's

Image
20140218_131319 by marley4us1985, on Flickr

Cut it down to the size I would need for the botton to work, this may take a couple of tries to get perfect. so cut it long and trim down
Image
20140218_131801 by marley4us1985, on Flickr


Used my dremel to cut the rod to shop, but it always leaves burn markes
Image
20140218_131805 by marley4us1985, on Flickr

Sanded the burn markes out, and smoothed the edges
Image
20140218_131955 by marley4us1985, on Flickr


Use a wood screw in the end of the dowel, and cut the head off. I tried a nail at first and it slips off too easy, sorry the pic should have been with the wood screw
Image
20140218_132205 by marley4us1985, on Flickr



Clamped it to the drill!!
Image
20140218_132227 by marley4us1985, on Flickr

Sand down the tip of the dowel so you can slid it through your 5/8 hole, but the bigger portion of dowel stops if from falling out
Image
20140218_132238 by marley4us1985, on Flickr

Like this
Image
20140218_133128 by marley4us1985, on Flickr

Then stain it to match your other wood items!
Image
20140218_140538 by marley4us1985, on Flickr

Image
20140218_140638 by marley4us1985, on Flickr

a little clear to make it look shinny :)
Image
20140218_141302 by marley4us1985, on Flickr

All done with wooden button and all
Image
20140218_160228 by marley4us1985, on Flickr

Image
20140218_160144 by marley4us1985, on Flickr

Image
20140218_160212 by marley4us1985, on Flickr

(ps the ebrake is bent to the side cause I have a SR20det motor and trans otherwise there would be interference with the shifter)

Re: wood shift knob to match your wood steering wheel

Posted: Thu Feb 20, 2014 3:12 pm
by oldeskewltoy
Brazilian cherrywood

Image

...the wood wheel, shift knob... AND dash inlay :o
Image

Re: wood shift knob to match your wood steering wheel

Posted: Mon Mar 03, 2014 10:47 pm
by Brendoninhawaii
woah bro, did you paint your nardi wheel that teal color?

Re: wood shift knob to match your wood steering wheel

Posted: Tue Mar 04, 2014 12:10 am
by marley4us
yup :)

Re: wood shift knob to match your wood steering wheel

Posted: Wed Aug 27, 2014 8:13 am
by subiemonger
That's awesome, did you thread the shift knob?

Re: wood shift knob to match your wood steering wheel

Posted: Fri Aug 29, 2014 7:57 am
by saiGone
*This DIY sponsored by Sapporo :P

Diggin the wood grain

Re: wood shift knob to match your wood steering wheel

Posted: Sun Aug 31, 2014 2:17 am
by marley4us
Ya I welded a bolt with the right thread pitch and a long nut it was like 5 nuts but together and glued it in!


Ya haha Sapporo, and Asahi sponsored!

Re: wood shift knob to match your wood steering wheel

Posted: Thu Oct 09, 2014 10:26 am
by Fltc86
now thats awesome!!

Re: wood shift knob to match your wood steering wheel

Posted: Wed Nov 26, 2014 4:33 am
by lmaz81
That e brake handle is dope. Whats the od of the wood.

Re: wood shift knob to match your wood steering wheel

Posted: Thu Mar 17, 2016 12:10 am
by mashi2choco
Damn, that's awesome. Good craftsmanship!

Re: wood shift knob to match your wood steering wheel

Posted: Mon Mar 28, 2016 5:13 pm
by Truenoboy843
wow that wheel is awesome!!! so is the shift knob!