January 2013
Still building parts for the AE86 GT-S


1 Piece light weight drive shaft
13 lbs 10 oz
over 7 lbs lighter than stock!!!
$355 plus shipping ($400 shipped in the USA)

Flex pipe to Delete Cat Converter
$72 shipped


4AGE Clutches
*200 mm Custom hand build disk in San Jose, Ca
$335 and up
*212 mm Custom hand build disk in San Jose, Ca
$350 and up
*224 mm Custom hand build disk in San Jose, Ca
$375 and up

Can Also make clutches with W series spline
All clutches are made to order (takes 5~10 working days)
$375 and up

Light weight flywheels also available such as Generic, Toda, Race Gear
$200 and up


LSD bearing Kit $150
2 pinion bearings
2 Diff bearings
OEM Toyota Pinion Seal
OEM Toyota Crush Sleeve
OEM Toyota Pinion Nut


Brake Pads Sets
Carbon Metallic (high dust)
$50 Fronts
$50 Rears


Brake Rotors Blank
Made in the USA
$25 Fronts
$25 Rears


Uncle Bob Brand Steering wheels $129
350 mm Diameter
Suede or Perforated leather
Deep Cone or Traditional

Also able to Order and Ship most OEM Toyota Parts
e-mail me if you have any questions

Thanks

Max

Maxfrommisawa@aol.com

great your back!
So i measured and measured and now im 100% its 230mm.(surface area clutch) (its an ae101)
its this correct then?
I would need a clutch kit for a w58.

AE101 GZE?

Max

check your email.

Illegal_Garage wrote:AE101 GZE?

Max

yes its a ae101 gze the last version of the gze

what transmission are you going to use?
I am not sure if it will fit in a W series bellhousing
also i need a pic of your flywheel
there was a few diffrent ones for GZE

Max

W58
http://i48.tinypic.com/2w22zhh.jpg
I have a niteparts bellhousing and it hits the belhousing but i was gonna grind the inside until it rotates
Or will the clutch also hit the bellhousing?
I will get a picture of the flywheel as soon as the snow melts,impossible right now since the car isnt at home

the clutch protrudes quite a bit
I dont know if you are able to grind off that much material
230mm clutch might be over kill
I have seen a turboed 4AGE in Takahiro's (green Levin built by Blacktrax) car making 293hp and he ran a 200mm clutch with no problems

Max

Illegal_Garage wrote:the clutch protrudes quite a bit
I dont know if you are able to grind off that much material
230mm clutch might be over kill
I have seen a turboed 4AGE in Takahiro's (green Levin built by Blacktrax) car making 293hp and he ran a 200mm clutch with no problems

Max

yes thats my cocern also.
If i would use another set however i would like the 225 mm gze flywheel&kit.(i no longer have 200mm flywheel so i will need to buy one then)
those seem very common.

that should fit the niteparts bellhousing+w58 right?
do you still have resurfaced flywheels?

I don't have any more good used flywheels
I would have to sell you a new one

Max

Illegal_Garage wrote:I don't have any more good used flywheels
I would have to sell you a new one

Max

how much does an oem new 225mm flywheel cost?

best regards

http://www.ebay.com/itm/1988-1989-Toyot ... mtr&_uhb=1

like that?

Max

looks good,are those holes in the back normal?

I dunno should contact the seller on eBay

Max

waiting for an answer,
can you pm me a price for the clutch kit for w58 225mm flywheel?

ditn wrote:looks good,are those holes in the back normal?

Yes, those holes are normal, it's where they removed material to balance the flywheel.

Ditn I am not the one selling the flywheel.
Also when dealing with a GZE you would have to ship me your flywheel
as some of the GZE flywheels have an odd mounting configuration
This is to insure you get the correct pressure plate

Max

Illegal_Garage wrote:Ditn I am not the one selling the flywheel.
Also when dealing with a GZE you would have to ship me your flywheel
as some of the GZE flywheels have an odd mounting configuration
This is to insure you get the correct pressure plate

Max

Since i live in belgium i think it would be best(if you can&its a good flywheel) if you would buy the flywheel and add it to the clutch kit
Else i have to buy the flywheel get it shipped to belgium and then back to the usa with double douane charges.

Send me an e-mail and I will see what I can do for you

Max

can you do clutches/flywheels for Beams 3sge?

i'd be very interested in buying a good clutch/flywheel combo. Otherwise I'm going to blow my life savings on an os giken..

Yea I have done a BEAMS before

Max

emailing you now.

i have sent you an email.

drove up to SJ and bought a driveshaft 2 nights ago, installed it last night
it was very professionally packaged, quality looks great. drove it on the freeway, no problems so far
car feels quicker/more responsive. best part is the joints are serviceable

Thanks for the positive feedback Bing

Max

wrong email so resent mail

OK got it and working on your request.

Max

To the top
Thanks

Max

Max, a friend of mine said you used to sell Illegal Garage brand flywheels? he has one and is very happy with it. do you still sell these?

e-mail me for more info about the flywheels

Max