The ultimate 4A-GZE, ported head, HKS cams, SC14, standalone
-
- Club4AG Enthusiast
- Posts: 129
- Joined: Thu Jan 10, 2013 10:32 pm
- Location: Colorado Springs, CO
The ultimate 4A-GZE, ported head, HKS cams, SC14, standalone
I'm unloading my never fired machine shop fresh 4A-GZE, tell me how you want it built. It's currently just an assembled shortblock but I have my immaculately clean ported/deburred smallport head for it with HKS valve springs, HKS 264/256 cam set, ARP head studs, powdercoated cam covers, hand built intake manifold built expressly to clear my ported 1G-GZE supercharger, bigass Cusco Powerball 4-1 header with custom built 2.5" b-pipe, SDS standalone EMS, 170mm crank pulley with magnets for the SDS pickup, accessory mount built to accept the hall sensor, this is the motherlode. The block has been "ported" as well to allow oil to drain back quicker and prevent casting sand from breaking off at high RPM. The oil pump is a factory Toyota smallport pump that was disassembled, cleaned, inspected per the BGB, and reassembled/installed. The pistons are .5mm oversized Toyota 8.9:1 forged slugs and rings, bearings, gaskets are ALL Toyota.
Shortblock sold!
Ported smallport head with HKS springs, $500. It's been shaved a total of .017" while in my posession and 16 cut valves were installed back in Okinawa. There might be 10k total on this valve job. I recently had it installed on my engine in my AE92, so bits of paint are still sticking to it. I'll clean those off.
Chambers deshrouded.
Ported exhaust ports, taken out to match a now discontinued TRD exhaust gasket. Also matches the blacktop gasket.
Probably can't see the intake work from this old shot, but I didn't hog the intake out like I did the exhaust. I just gasket matched it and blended it. Also took out the ridges in the throats like I did in the exhaust, that's where the easy money is.
And here's how clean it is from the top side.
Intake manifold sold!
Ported/modified SC14 sold!
Unmodified SC14 sold!
SDS sold!
MSD sold!
Email d_mozader at hot mail dot com. If interested, I'm willing to work with you on a package deal too.
Shortblock sold!
Ported smallport head with HKS springs, $500. It's been shaved a total of .017" while in my posession and 16 cut valves were installed back in Okinawa. There might be 10k total on this valve job. I recently had it installed on my engine in my AE92, so bits of paint are still sticking to it. I'll clean those off.
Chambers deshrouded.
Ported exhaust ports, taken out to match a now discontinued TRD exhaust gasket. Also matches the blacktop gasket.
Probably can't see the intake work from this old shot, but I didn't hog the intake out like I did the exhaust. I just gasket matched it and blended it. Also took out the ridges in the throats like I did in the exhaust, that's where the easy money is.
And here's how clean it is from the top side.
Intake manifold sold!
Ported/modified SC14 sold!
Unmodified SC14 sold!
SDS sold!
MSD sold!
Email d_mozader at hot mail dot com. If interested, I'm willing to work with you on a package deal too.
Last edited by Crownvicman289 on Sun Mar 23, 2014 9:59 am, edited 6 times in total.
Re: The ultimate 4A-GZE, ported head, HKS cams, SC14, standa
Man I wish I could pick this up as a whole haha. Glws sir
-
- Club4AG Enthusiast
- Posts: 129
- Joined: Thu Jan 10, 2013 10:32 pm
- Location: Colorado Springs, CO
Re: The ultimate 4A-GZE, ported head, HKS cams, SC14, standa
Throw enough money at me and it's yours.
-
- Posts: 6
- Joined: Sat Aug 31, 2013 9:49 am
Re: The ultimate 4A-GZE, ported head, HKS cams, SC14, standa
interested on the cams can you pm me.
-
- Club4AG Enthusiast
- Posts: 129
- Joined: Thu Jan 10, 2013 10:32 pm
- Location: Colorado Springs, CO
-
- Club4AG Enthusiast
- Posts: 129
- Joined: Thu Jan 10, 2013 10:32 pm
- Location: Colorado Springs, CO
Re: The ultimate 4A-GZE, ported head, HKS cams, SC14, standa
Cams/gears sold, header pending.
Re: The ultimate 4A-GZE, ported head, HKS cams, SC14, standa
pretty good deal for a ported head and oil-squirter block
If I had a job I would be all over this
If I had a job I would be all over this
Davegt27 Code One Racing
-
- Club4AG Enthusiast
- Posts: 129
- Joined: Thu Jan 10, 2013 10:32 pm
- Location: Colorado Springs, CO
Re: The ultimate 4A-GZE, ported head, HKS cams, SC14, standa
Get a job and buy it up!
Shortblock sold!
Shortblock sold!
-
- Club4AG Enthusiast
- Posts: 129
- Joined: Thu Jan 10, 2013 10:32 pm
- Location: Colorado Springs, CO
-
- Posts: 1
- Joined: Mon Jan 14, 2013 9:58 pm
Re: The ultimate 4A-GZE, ported head, HKS cams, SC14, standa
Pm'd about the modded sc14
-
- Club4AG Enthusiast
- Posts: 129
- Joined: Thu Jan 10, 2013 10:32 pm
- Location: Colorado Springs, CO
Re: The ultimate 4A-GZE, ported head, HKS cams, SC14, standa
PM replied. I also added more specific information regarding the SC14 fitment in the original post.
-
- Club4AG Enthusiast
- Posts: 129
- Joined: Thu Jan 10, 2013 10:32 pm
- Location: Colorado Springs, CO
Re: The ultimate 4A-GZE, ported head, HKS cams, SC14, standa
Ported SC14 sold, intake manifold pending.
-
- Club4AG Enthusiast
- Posts: 129
- Joined: Thu Jan 10, 2013 10:32 pm
- Location: Colorado Springs, CO
Re: The ultimate 4A-GZE, ported head, HKS cams, SC14, standa
Ported SC14 and intake manifold sold!
I still have the ported head, the unmodified SC14, and the SDS system available.
I still have the ported head, the unmodified SC14, and the SDS system available.
Re: The ultimate 4A-GZE, ported head, HKS cams, SC14, standa
U got pm sir
'85 GT-S project since 2010
-
- Club4AG Enthusiast
- Posts: 118
- Joined: Mon Jan 14, 2013 9:20 pm
- Location: new jersey
Re: The ultimate 4A-GZE, ported head, HKS cams, SC14, standa
bump for a great seller ! and some legit parts plus super fast shipping
-
- Club4AG Enthusiast
- Posts: 129
- Joined: Thu Jan 10, 2013 10:32 pm
- Location: Colorado Springs, CO
Re: The ultimate 4A-GZE, ported head, HKS cams, SC14, standa
Bump for the head, SC14, and SDS.
-
- Club4AG Enthusiast
- Posts: 129
- Joined: Thu Jan 10, 2013 10:32 pm
- Location: Colorado Springs, CO
Re: The ultimate 4A-GZE, ported head, HKS cams, SC14, standa
I can't believe nobody wants a ported head at half what it costs to get a head ported. Still have it, the SC14 that bolts to an SC12 mount, and the SDS that gets you past the low end leanout of the USDM GZE ECU and the 5,5oo RPM power drop of the JDM GZE DLI ECU.
-
- Club4AG Enthusiast
- Posts: 129
- Joined: Thu Jan 10, 2013 10:32 pm
- Location: Colorado Springs, CO
Re: The ultimate 4A-GZE, ported head, HKS cams, SC14, standa
SDS, MSD, SC14 sold! Still have the head.
-
- Club4AG Regular
- Posts: 17
- Joined: Thu Mar 13, 2014 5:14 pm
- Location: Eastern Washington
Re: The ultimate 4A-GZE, ported head, HKS cams, SC14, standa
Crownvicman289 wrote: I have my immaculately clean ported/deburred smallport head for it with HKS valve springs, HKS 264/256 cam set, ARP head studs, powdercoated cam covers
Is all of the above included in the sale? also are you willing to ship to Washington? If so what is the total and how will you package it and ship?
-
- Club4AG Enthusiast
- Posts: 129
- Joined: Thu Jan 10, 2013 10:32 pm
- Location: Colorado Springs, CO
Re: The ultimate 4A-GZE, ported head, HKS cams, SC14, standa
Cams are already sold, I'd ship in a cardboard box with stock cams installed to keep the buckets and shims from flying all over. Price of the head is for the head only (with stock cams though). Email me and we can work something out.