Search found 42 matches

by nyberrg
Mon Aug 30, 2021 11:29 am
Forum: TECH: 4A-GE ENGINE
Topic: Return #5: Spare engine boogaloo
Replies: 7
Views: 7229

Re: Return #5: Spare engine boogaloo

I had a bunch of issues with things outside of the engine. But I made my deadline and went on my trip. The new engine performs good so far. Sounds nice and runs great... until it didn't. One of the rubber flanges I mount my carbs in decided to break the night before causing the engine to run on thre...
by nyberrg
Wed Aug 18, 2021 12:07 pm
Forum: TECH: 4A-GE ENGINE
Topic: Return #5: Spare engine boogaloo
Replies: 7
Views: 7229

Re: Return #5: Spare engine boogaloo

As you mentioned you believe you were out of spec.......... Still had one crank that was good to go. There was a distinct difference between the good and the bad. Checked the main and rod bearing clearances as the Toyota repair manual said and it was good. https://i.imgur.com/s2tPSvr.jpg Deadline i...
by nyberrg
Mon Aug 09, 2021 7:46 am
Forum: TECH: 4A-GE ENGINE
Topic: Return #5: Spare engine boogaloo
Replies: 7
Views: 7229

Re: Return #5: Spare engine boogaloo

Out on deep waters with measurements and honing equipment. :lol: https://i.imgur.com/im3b1PG.jpg Things look to be in order with the 7-rib block. One crank is good to go. Checked the pistons quickly and they seem to be ok. I will do the proper calculations on tolerances to the cylinders next.
by nyberrg
Fri Aug 06, 2021 12:19 am
Forum: TECH: 4A-GE ENGINE
Topic: Return #5: Spare engine boogaloo
Replies: 7
Views: 7229

Re: Return #5: Spare engine boogaloo

In my hunt for bearings I got some from the local Toyota dealer. When they showed up it turned out it was only ONE of each. One crank bearing, one rod bearing. Doing the math of how much a full set would cost me I noped out. With Flo's being closed for vacation I don't know where to find bearings in...
by nyberrg
Thu Aug 05, 2021 2:36 am
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30519

Re: HIGH comp Big port carby build with MANY questions

Is that a crack in the liner on the far left...??? Looks a bit too vertical... Maybe? I haven't inspected the block cause I have no plans on using it ever. I'm pretty sure those lines were there when I got it back from the machine shop but I couldn't feel them so I didn't really care. I'll take a l...
by nyberrg
Thu Aug 05, 2021 2:31 am
Forum: TECH: 4A-GE ENGINE
Topic: Return #5: Spare engine boogaloo
Replies: 7
Views: 7229

Re: Return #5: Spare engine boogaloo

I'll update this thread and leave the old one. I dissasembled the 7-rib block and found bearings that were not in the best shape. The crank bearings were worn but not discolored in any way. Conrod bearings were worn and brown-ish in some places. I meassured the crank and the rod journals seem to be ...
by nyberrg
Tue Jul 27, 2021 3:46 am
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30519

Re: HIGH comp Big port carby build with MANY questions

I cleaned the piston off to check for damage, that'swhy it's so much cleaner than the other one. Although there has been water in the cylinders too for sure. The image is cylinder #4 and it is pretty fucked. My guess is due to the ring gap being too tight, maybe? The block is done so I'm moving on. ...
by nyberrg
Sat Jul 24, 2021 8:13 am
Forum: TECH: 4A-GE ENGINE
Topic: Return #5: Spare engine boogaloo
Replies: 7
Views: 7229

Return #5: Spare engine boogaloo

As expected my engine build did not last long. It's time to salvage what's possible. More details coming tomorrow but for now I have one question. Is it possible to use a big port (ae86) head on a 7-rib (smallport, ae92) block? The block has what looks like an external oil return. The internal retur...
by nyberrg
Sat Jul 24, 2021 5:17 am
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30519

Re: HIGH comp Big port carby build with MANY questions

Doesn't look like I have to worry about the oil. Cause my block is fucked either way :lol:

https://i.imgur.com/YS47KSY.jpg
by nyberrg
Fri Jul 23, 2021 7:45 am
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30519

Re: HIGH comp Big port carby build with MANY questions

Well, I got the head off Images were too large to embed... https://i.imgur.com/t1pbo59.jpg https://i.imgur.com/SGJHc3Z.jpg https://i.imgur.com/P9weFH2.jpg https://i.imgur.com/d4YcKYp.jpg Doesn't look fantastic :lol: One thought that popped in my head is if the oem gasket works with bigger bore pisto...
by nyberrg
Fri Jul 23, 2021 1:34 am
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30519

Re: HIGH comp Big port carby build with MANY questions

I've got a 3 layer 0.5mm TRD gasket laying around. But there's a reason why I didn't use that the first time around... Engine is a big port, head is shaved a bit (just to resurface after warping, not with the intention to increase compression), stroke is standard but the pistons are some wisecos wit...
by nyberrg
Thu Jul 22, 2021 12:31 pm
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30519

Re: HIGH comp Big port carby build with MANY questions

I'm curious as to why your temperature would go up to 90 and then drop quickly when you rev the engine. Do you have a thermostat installed ? Do you have an electric cooling fan ? I'm pretty sure the water doesn't circulate as well on idle cause of the radiator size. If I look in to the radiator whe...
by nyberrg
Wed Jul 21, 2021 5:28 am
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30519

Re: HIGH comp Big port carby build with MANY questions

https://www.club4ag.com//forums/viewtopic.php?f=9&t=12283 Cheers... jondee86 Yah, I read that thread and understand the basics of it. I don't really have an issue with pressure, blowing hoses, or temperature though. It's just that water dissapears. Only theory I got is that it could be a very, ...
by nyberrg
Tue Jul 20, 2021 1:17 pm
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30519

Re: HIGH comp Big port carby build with MANY questions

Might as well continue on this thread as it exists and it is about the same engine. Everything is chugging along nicely. I drive my car regularly and the engine is pretty much good, except for a few things... The cooling system is very home made with FWD 4age parts. I use an NB Miata radiator with a...
by nyberrg
Sat Jul 25, 2020 5:31 am
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30519

Re: HIGH comp Big port carby build with MANY questions

Do you have a print out of the dyno?? Here's a photo of the computer screen from one run https://i.imgur.com/nHOhoFt.jpg Apparently it's too large to embed :? I didn't get to fiddle with cam timing as the dyno decided to break and read my RPMs somewhere around 170k. For now it runs with jets drille...
by nyberrg
Fri Jul 24, 2020 12:24 am
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30519

Re: HIGH comp Big port carby build with MANY questions

24milespergallon wrote:What distributor are you using?

No distributor. Crank sensor and trigger wheel.
by nyberrg
Thu Jul 09, 2020 12:57 pm
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30519

Re: HIGH comp Big port carby build with MANY questions

First few dyno pulls are done. And it runs pretty good. My carb adjustments do not seem to be close to yours though, mr2mk1Hero.. It ran on 160 main jets, and it still needs more fuel. I haven't played with the needles at all though cause I can't figure out how to separate the needle from the diaphr...
by nyberrg
Fri May 08, 2020 7:30 am
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30519

Re: HIGH comp Big port carby build with MANY questions

As someone who has gone through a carb build here's my advice. Get an AFR gauge if you haven't already. I think I remember your name actually, we messaged on Instagram once? And I mentioned an AFR gauge? Tuning carbs without one is just guesswork. Someone with A LOT of experience can tune carbs wit...
by nyberrg
Fri Apr 24, 2020 2:20 am
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30519

Re: HIGH comp Big port carby build with MANY questions

Here is a video on valve clearance: https://www.youtube.com/watch?v=nB8uVQxr3Pw And one on valve lapping: https://www.youtube.com/watch?v=YA-edFt6TuU Some people say that valve lapping is not necessary these days, l'll not comment on that! Thanks! that's all within spec, lapping was done by pros an...
by nyberrg
Thu Apr 23, 2020 1:01 am
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30519

Re: HIGH comp Big port carby build with MANY questions

I'm curious about the 22psi variance for one cylinder since it's a 10%+ gap from the other three cylinders on a fresh build. Hot or cold test? If cold, try one at temp. Motor run in enough for the rings to be seated? Did the combustion chambers hold alcohol/water once the valves were lapped? Valve ...
by nyberrg
Mon Apr 20, 2020 1:30 am
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30519

Re: HIGH comp Big port carby build with MANY questions

totta crolla wrote:No assumption required, anyone who builds an engine and is then surprised by the compression ratio...

"I don't really know what I built"
"I ran a compression test on the cylinders and they all read high, really high, like 15 bar high"


Refer to previous response ¯\_(ツ)_/¯
by nyberrg
Sun Apr 19, 2020 11:54 am
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30519

Re: HIGH comp Big port carby build with MANY questions

i think totta was stressing the importance of getting the combination totally 'dialed in'. Tuning can make or break any project. VERY ez to wind up with costly parts delivering shitty performance I didn't ask "is it important to tune a car?" though. I know that already. I simply wanted so...
by nyberrg
Sun Apr 19, 2020 11:46 am
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30519

Re: HIGH comp Big port carby build with MANY questions

totta crolla wrote:Sorry if the truth doesn't suit you.


The truth is it's a fucking work in progress. I could tell every detail of what I have done and so on so that you might understand where I'm coming from but I wont. Please just stop assuming im stupid instead.
by nyberrg
Wed Apr 15, 2020 5:18 am
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30519

Re: HIGH comp Big port carby build with MANY questions

You asked this question: "What supporting mods are the most important?" Throwing those camshafts in and having no facility to fine tune them is a complete waste of time. Here is the thing, to make the power that your build may be capable of you will need to set the carbs up properly but y...
by nyberrg
Tue Apr 14, 2020 1:27 pm
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30519

Re: HIGH comp Big port carby build with MANY questions

I hate those pistons..... https://kgpengineering.com/wp-content/uploads/wis-k506m815_w.jpg dome volume approaching 5cc... just too much. Jondee's recommendation is good... that may help. You wrote the cams as 264/272 - am I right that you have the 264 cam on the intake side? Any chance you can swap...
by nyberrg
Tue Apr 14, 2020 1:25 pm
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30519

Re: HIGH comp Big port carby build with MANY questions

- Blowby is primarily driven by the combustion pressure which is many times higher than the cranking pressures. So blowby is pretty much proportional to engine rpm. A new engine with tight clearances and good ring sealing won't have a lot of blowby and the standard single cam cover vent will be ade...
by nyberrg
Sun Apr 12, 2020 10:07 am
Forum: TECH: 4A-GE ENGINE
Topic: HIGH comp Big port carby build with MANY questions
Replies: 45
Views: 30519

HIGH comp Big port carby build with MANY questions

Yo! So this is gonna be a pretty long explanation before getting to the point.. I've been building a big port for a couple of years, as fast as my wallet has let me. The parts are a mix of things I came upon and planned purchaces, I don't really know what I built :? Anyways, it's together now and id...
by nyberrg
Mon Aug 19, 2019 2:20 am
Forum: TECH: 4A-GE ENGINE
Topic: Bike carb conversion: Gas pedal travel issue
Replies: 4
Views: 6018

Re: Bike carb conversion: Gas pedal travel issue

Ended up having a bigger wheel fabricated and welded to the smaller wheel on the carbs. Need to relocate the cable a bit for it to be 100% but it seems like a good solution since removing the stock wheel seemed hard on my carbs.
by nyberrg
Wed Aug 14, 2019 12:58 pm
Forum: TECH: 4A-GE ENGINE
Topic: Bike carb conversion: Gas pedal travel issue
Replies: 4
Views: 6018

Bike carb conversion: Gas pedal travel issue

Been building a 16v on carbs for a while now. Gonna run Mikuni carbs from a Kawasaki Ninja ZX6R. Today I ran in to an issue while trying out throttle cables. Since the throttle cable mount point on the carbs is so small in diameter compared to the stock 4age I can barely push the pedal down an inch ...
by nyberrg
Thu Oct 19, 2017 11:52 pm
Forum: TECH: 4A-GE ENGINE
Topic: 4age on bike carbs
Replies: 30
Views: 37110

Re: 4age on bike carbs

Hey! What parts did you get in the carburetor kit and what parts did you buy separately? Is the vacuum distributor thingie part of the kit? I'm gonna do the same conversion on my Carina, just need to set up a budget :lol: