Search found 2256 matches

by jondee86
Sat Aug 18, 2018 3:17 pm
Forum: TECH: 4A-GE ENGINE
Topic: 4age engine brackets
Replies: 7
Views: 133

Re: 4age engine brackets

Can't answer that question. But I do recall that when installing a converted FWD 16V engine into an AE86, there was an alignment issue. FWD crank pulleys have a slightly different offset to RWD crank pulleys, and to make everything line up, you have to use all FWD pulleys or all RWD pulleys. That is...
by jondee86
Sat Aug 18, 2018 3:02 pm
Forum: TECH: Corolla AE86
Topic: Ae86 strut mount same as FWD?
Replies: 3
Views: 125

Re: Ae86 strut mount same as FWD?

For the benefit of anyone who stumbles onto this thread in the future,
what was your conclusion from studying the parts catalogs ? Are Ae86
strut mount same as FWD?

Cheers... jondee86
by jondee86
Fri Aug 17, 2018 6:53 pm
Forum: TECH: 4A-GE ENGINE
Topic: 4age engine brackets
Replies: 7
Views: 133

Re: 4age engine brackets

Yes... one is a casting and the other is pressed steel. Note that the engine mounts have two parts... a pressed steel cover and a rubber "sandwich" with a fixing stud on either side. The engine mounts are the same both sides. Cheers... jondee86 PS: You might find this thread from another s...
by jondee86
Fri Aug 17, 2018 3:55 pm
Forum: TECH: 4A-GE ENGINE
Topic: 4age engine brackets
Replies: 7
Views: 133

Re: 4age engine brackets

Pretty sure that AE86 GTS (I think the same as SR5) OEM brackets will be your best bet. They bolt up with one bolt in conflict with another bracket, but easily fixed. Then you can bolt on the OEM AE86 engine mounts and that just leaves the mount to chassis rail part to be fabbed. This pic shows the ...
by jondee86
Fri Aug 10, 2018 5:49 pm
Forum: TECH: 4A-GE ENGINE
Topic: 4AGE automatic
Replies: 26
Views: 412

Re: 4AGE automatic

Yeah, six gears would be too many for me. It's more about being able to buy the bits needed for the conversion and having the gear lever sit in the stock location. I would be happy with four gears, and I have a T-40 and a 3.9 CW&P sitting in the garage. When the T-50 dies I am going to fit those...
by jondee86
Fri Aug 10, 2018 2:58 pm
Forum: OWNERS and BUILDERS
Topic: My '93 Toyota Corolla Levin AE101 "Di Analys"
Replies: 5
Views: 188

Re: My '93 Toyota Corolla Levin AE101 "Di Analys"

Welcome aboard Matthew :) Sure wish I lived somewhere that you could get a radiator fixed on a public holiday, and workshops stayed open until the job was done. Hope you bought those guys a cold drink when they were done :) Glad you explained how you came to name your car. I read "dialysis"...
by jondee86
Fri Aug 10, 2018 1:56 am
Forum: TECH: 4A-GE ENGINE
Topic: 4AGE automatic
Replies: 26
Views: 412

Re: 4AGE automatic

Yusss... I don't have a racecar so the idea I had in mind was to have an auto with an aftermarket controller so that I could either let the controller change gears in full auto mode or switch to a "tiptronic" mode with programmable shift points. Tracked down a supplier and even fould a guy...
by jondee86
Thu Aug 09, 2018 12:19 am
Forum: TECH: Corolla AE86
Topic: Ae86 strut mount same as FWD?
Replies: 3
Views: 125

Re: Ae86 strut mount same as FWD?

These are the Toyota OEM part numbers... 48609-20060 Corolla FWD DLX, DLX All Trac, FX, FX16, FX16 GTS, GTS, LE, SR5, SR5 All Trac 48609-12130 LH , Corolla RWD Sport DLX, Sport GTS, Sport SR5 48609-12100 RH , Corolla RWD Sport DLX, Sport GTS, Sport SR5 I am not aware that the FWD and RWD parts inter...
by jondee86
Wed Aug 08, 2018 2:13 pm
Forum: TECH: 4A-GE ENGINE
Topic: My 4age-t
Replies: 5
Views: 159

Re: My 4age-t

Nice work !!! I'm guessing racecar as no filter :)

Cheers... jondee86
by jondee86
Tue Aug 07, 2018 2:47 pm
Forum: TECH: 4A-GE ENGINE
Topic: 4AGE automatic
Replies: 26
Views: 412

Re: 4AGE automatic

That's the one. Trans is used behind the 4AC but will bolt up to a 4AGE as they are
both A-Series engines. You just need to figure out the flexplate by looking at the cars
mentioned above.

Morris Minor !!! Wouldn't have thought there would be many of those in the States :)

Cheers... jondee86
by jondee86
Tue Aug 07, 2018 4:34 am
Forum: TECH: 4A-GE ENGINE
Topic: 4AGE automatic
Replies: 26
Views: 412

Re: 4AGE automatic

Interesting :) Running an auto has been in the back of my mind for a long time. Looked at fitting a later model auto from an Altezza but just too much work to get it installed in an AE86. Control would be a problem as well, as it would need an aftermarket trans controller and that is another heap of...
by jondee86
Tue Aug 07, 2018 12:36 am
Forum: TECH: 4A-GE ENGINE
Topic: 4AGE automatic
Replies: 26
Views: 412

Re: 4AGE automatic

A42DL as found in the SR5/AE85 with the 4AC engine. This will bolt right up to the 4AGE and the only problem you will have is locating a suitable 8-bolt flexplate. The 4AC has a 6-bolt crank and the 4AGE has an 8-bolt, but I am lead to believe that the flexplate from some of the FWD 4AGE Corollas wi...
by jondee86
Sat Aug 04, 2018 3:39 pm
Forum: TECH: 4A-GE ENGINE
Topic: Tvis tick/knock
Replies: 4
Views: 126

Re: Tvis tick/knock

So you have the same problem as this guy ?? https://www.youtube.com/watch?v=QYr9nloWzoM You can check the vacuum servo (actuator) by using a hand pump like a Mityvac and applying vacuum directly to the actuator. If the servo cannot hold vacuum and leaks down in just a few seconds, then the diaphragm...
by jondee86
Fri Jul 27, 2018 3:06 pm
Forum: TECH: Corolla AE86
Topic: More issues...engine intermittently stumbles under load.
Replies: 20
Views: 575

Re: More issues...engine intermittently stumbles under load.

Should I go all out with a Walbro? Or would any pump for our car from Rockauto.com be sufficient? I bought a generic pump like this one... https://www.trademe.co.nz/motors/car-parts-accessories/toyota/other/listing-1707577285.htm?rsqid=bcbb6a1f090c49d7baa80874e6f40939 Didn't come with a filter, but...
by jondee86
Thu Jul 26, 2018 5:32 pm
Forum: TECH: Corolla AE86
Topic: More issues...engine intermittently stumbles under load.
Replies: 20
Views: 575

Re: More issues...engine intermittently stumbles under load.

But also note that I couldnt test it with the engine under load or in gear...i was just revving it in the garage. As you will have noticed while holding the revs steady, free revving only requires a very small throttle opening and because there is no load on the engine, there is very little fuel co...
by jondee86
Tue Jul 24, 2018 4:45 pm
Forum: TECH: Corolla AE86
Topic: More issues...engine intermittently stumbles under load.
Replies: 20
Views: 575

Re: More issues...engine intermittently stumbles under load.

Something like this would do the job so long as you don't mind stopping the car and lifting the hood to see what's going on... http://www.bmracing.com/products/46054-fuel-pressure-gauge-for-acura-honda-mitsubishi-eagle-talon-plymouth-laser/# My car seems to run fine on the factory FPR so I'm not loo...
by jondee86
Tue Jul 24, 2018 2:37 pm
Forum: TECH: Corolla AE86
Topic: More issues...engine intermittently stumbles under load.
Replies: 20
Views: 575

Re: More issues...engine intermittently stumbles under load.

I think that you should be checking fuel pressure this time round :) Sounds
like something is getting clogged or the fuel pump is dying.

Cheers... jondee86
by jondee86
Thu Jul 19, 2018 9:30 pm
Forum: TECH: 4A-GE ENGINE
Topic: Weird 4A-GE idle problem
Replies: 12
Views: 465

Re: Weird 4A-GE idle problem

Hmmm... it seems that your AAV is operating much as expected except for the idle dropping to 500rpm sometimes. As totta crolla points out, when you add electrical load a small solenoid valve should open to allow extra air into the manifold via one of the small spigots on top of the throttlebody. Thi...
by jondee86
Thu Jul 19, 2018 2:41 pm
Forum: TECH: 4A-GE ENGINE
Topic: Weird 4A-GE idle problem
Replies: 12
Views: 465

Re: Weird 4A-GE idle problem

Here is a diagram showing the AAV... http://i.imgur.com/sRIfl.jpg I have never heard of anyone repairing one, but apparently you can still buy them new (for big $$$).... http://jp-carparts.com/toyota/part_detail.php?maker=toyota&type=231120&cartype=43&fig=2211&part=1173682 I'll have ...
by jondee86
Thu Jul 19, 2018 1:10 am
Forum: TECH: 4A-GE ENGINE
Topic: Hesitation @ lower rpm
Replies: 4
Views: 262

Re: Hesitation @ lower rpm

If you have an AFM, check that the flap inside is free to move and not binding or
sticking at low throttle openings.

Cheers... jondee86
by jondee86
Thu Jul 19, 2018 1:06 am
Forum: TECH: 4A-GE ENGINE
Topic: Weird 4A-GE idle problem
Replies: 12
Views: 465

Re: Weird 4A-GE idle problem

Hmmm... my bad :oops: I think that I read your post too quickly, and didn't pick up that your engine is actually doing the opposite to what it would if the AAV was blocked. To be clear; if the AAV is working the engine idles high on cold start and tapers down as the engine warms up. Normal is 2200rp...
by jondee86
Wed Jul 18, 2018 4:55 pm
Forum: TECH: 4A-GE ENGINE
Topic: Weird 4A-GE idle problem
Replies: 12
Views: 465

Re: Weird 4A-GE idle problem

What you describe are classic symptoms of how an engine behaves if the AAV (ISCV by another name) is not working. If you have have placed the whole valve in boiling water and seen that it moves 3 or 4mm, then the next thing to check is if the water from the coolant piping is actually circulating thr...
by jondee86
Wed Jul 04, 2018 6:14 pm
Forum: Fun Talk
Topic: what happened to the community
Replies: 77
Views: 12497

Re: what happened to the community

So I started talking to a guy I met through some craigslist posts. I thought he was a club4ag member because he is looking for something currently posted in the WTB section... His response: "Nah I haven’t been accepted to that :( or not sure if for some reason they’re not letting people in any...
by jondee86
Tue Jul 03, 2018 5:47 pm
Forum: TECH: 4A-GE ENGINE
Topic: 20v 4AGE ST Misfire/miss.
Replies: 16
Views: 1020

Re: 20v 4AGE ST Misfire/miss.

The remaining question is, was it oil volume? Or oil pressure? (Inside the puck) Optical sensors can be affected by anything that obstructs light getting from the emitter to the receiver. So dust, condensed moisture, carbon, insects or oil getting in the wrong place will eventually cause a problem....
by jondee86
Sat Jun 30, 2018 10:11 pm
Forum: TECH: Corolla AE86
Topic: Rear axle hub diameter
Replies: 7
Views: 302

Re: Rear axle hub diameter

0.375" = 3/8" = 9.52mm :) I don't see any problem in machining the axle flange down to fit inside the AW11 disc. Here is a pic of AE86 GTS axles for reference... http://i59.tinypic.com/f4r591.jpg In theory the if the studs stay in the same place, reducing the outside diameter of the flange...
by jondee86
Thu Jun 28, 2018 12:36 am
Forum: TECH: Corolla AE86
Topic: Rear axle hub diameter
Replies: 7
Views: 302

Re: Rear axle hub diameter

Rogue-AE95 wrote:I guess I should also ask... what is the thickness of the AE86 GTS rear hub?

I measured it at 9.4mm.

Cheers... jondee86
by jondee86
Tue Jun 26, 2018 4:06 pm
Forum: TECH: Corolla AE86
Topic: Rear axle hub diameter
Replies: 7
Views: 302

Re: Rear axle hub diameter

I've got a couple of axles here that were sold to me as being AE86 axles. The hub outside diameter measures 139.6mm near enough with cheap calipers :) The locating ring for the wheel measures 60mm and I think it is the center hole in the factory wheels that measures 60.1mm for a snug fit. Cheers... ...
by jondee86
Wed Jun 20, 2018 3:56 am
Forum: Fun Talk
Topic: Need a Toyo Expert...
Replies: 3
Views: 182

Re: Need a Toyo Expert...

Yusss... FWD offset, 4 x 100 lug PCD (AE86 needs 4 x 114.3) and the center hole
is too small for an AE86. But great wheels for a FWD Corolla :)

Cheers... jondee86
by jondee86
Mon Jun 18, 2018 9:56 pm
Forum: Want to BUY (seeking sellers)
Topic: canadian cluster, engine under cover
Replies: 2
Views: 234

Re: canadian cluster, engine under cover

This thing... factory aero :)

Image

Cheers... jondee86
by jondee86
Thu Jun 14, 2018 3:08 pm
Forum: TECH: 4A-GE ENGINE
Topic: Need help identified this
Replies: 6
Views: 545

Re: Need help identified this

The ISCV is bolted underneath the intake manifold at the rear of the engine. This might be helpful.... http://files.aeu86.org/manuals/blacktop/bt8-fi.pdf In a FWD installation you don't have much choice... you have to remove the whole intake manifold/throttle assembly to get access to the ISCV. But ...

Go to advanced search